Data requirements for neutron activation: Part I: Cross sections

Existing neutron cross section libraries such as EAF-2003 contain a large number of reactions. Of these only a small proportion are significant in the production of the nuclides that dominate activation quantities such as activity or γ-dose rate at various decay times. These reactions were identified in a recent extensive set of calculations on all the elements and reported in the ‘Activation Handbook’. These 1340 reactions are considered here and the set of reactions with no differential or integral data are listed and prioritised. A set of 339 reactions with very limited possibility of measurement are given; these require further study by theoretical calculations. A set of 100 reactions with either discrepant or no data, that might be measurable are listed and are recommended to be the subject of future experimental work.     

Decisive arrival law parameters and a general finite capacity queueing problem

This paper addresses the problem of finding the parameters of the arrival law which most significantly influence expected occupation and loss of a finite capacity queue. The input process is supposed to be ergodic and wide sense stationary. We show that it is mostly possible to fit an MMPP(2) to the decisive parameters of observational data. Numerical examples illustrate the importance of the decisive parameters, called key parameters, and also show the accuracy of the proposed fitting procedure. Finally, in the appendix we present the solution of the finite capacity queueing problem with Special Semi Markov Process (SSMP) arrivals and a general service strategy.     

On the dissipation process in Bi2Sr2Ca2Cu3O10 tapes and bulk samples with preferential grain orientation in zero external magnetic field

Current-voltage characteristics of Bi₂Sr₂Ca₂Cu₃O₁₀ tapes and bulk samples with preferentially oriented crystallites have been measured in zero applied magnetic field and for temperatures close to the mean-field critical-temperature,T _c0. It was shown that the power-law dependence,V=AI ^a, valid for two-dimensional systems, does not correctly describe the data, which clearly indicate the existence of a finite critical-current density,J _c. The experimentalI-V curves are fitted quite well with the model which attributes the finite critical-current density to the coupling between the CuO₂ double layers. It was found thatJ _c vanishes at a temperature value belowT _c0. This behavior can result from the occurrence of vortex fluctuation-induced layer decoupling and/or from the contribution of entropy to the vortex unbinding process.     

Information cut for clustering using a gradient descent approach

We introduce a new graph cut for clustering which we call the Information Cut. It is derived using Parzen windowing to estimate an information theoretic distance measure between probability density functions. We propose to optimize the Information Cut using a gradient descent-based approach. Our algorithm has several advantages compared to many other graph-based methods in terms of determining an appropriate affinity measure, computational complexity, memory requirements and coping with different data scales. We show that our method may produce clustering and image segmentation results comparable or better than the state-of-the art graph-based methods.     

双能X射线骨密度仪测定技术研究

以Ｌｕｎａｒ公司ＤＰＸ－Ｌ型双能Ｘ射线骨密度仪为例，研究引起测量误差的主要因素并提出质控措施。用自检模块、腰椎体膜评定仪器的体外测量精度好于１％。对１０位志愿者重复２次测量，体内精度对腰椎，ＭＰＤ（平均百分差）为０．４６，ＣＶ（变异系数）为０．７５；对股骨颈，ＭＰＤ为１．２６、ＣＶ为０．４７；Ｗａｒｄ’ｓ三角区ＭＰＤ为２．０１、ＣＶ为１．１４；大转子ＭＰＤ为１．６６、ＣＶ为０．７２。扫描图像由２位     

High-Pressure (up to 140 MPa) Dynamic Viscosity of the Methane and Toluene System: Measurements and Comparative Study of Some Representative Models

The dynamic viscosity of toluene and methane mixtures containing 25.03, 37.19, 49.95, 64.11, and 95.00 mol% methane has been measured using a falling-body viscometer. The measurements (280 data points) have been performed in the temperature range 293.15 to 373.15 K and at pressures up to 140 MPa. The data have been discussed in the framework of recent representative models (hard-sphere scheme, friction theory, and free-volume model) as well as with simple mixing laws and empirical models (particularly the LBC model and the self-referencing model) used in the literature. This comparative study shows that the average absolute deviation of the models is between 4.9 and 26.8%, and the maximum deviation is between 11.6 and 49.5%.     

动态交联热塑性弹性体增韧聚丙烯合金

用动态交联方法制备聚烯烃热塑性弹性体（ＴＰＯ）增韧聚丙烯，制备了具有低温冲击性能良好、综合力学性能比较均衡的聚丙烯合金。同时，研究了ＴＰＯ组成、工艺及基体组成与ＴＰＯ增韧聚丙烯共混物力学性能的关系。并通过差热扫描量热计和扫描电镜考察了共混物的形态结构。     

智能化红外焊缝检测仪的实时信号自相关分析

详细介绍了在改进红外焊缝检测仪的过程中实时信号的一种抗干扰方法－－自相关方法。重点离自相关方法的数学模型，软件框图及设计思想，并给出了实验结果。     

差分扩频技术在移动水声通信中的应用

提出了基于差分相干解调法的DS/BDPSK水声通信技术,在接收端采用差分相干解调的方法,解决了在水声通信中载波估计较难的问题,可克服传输过程中由于载波漂移产生的频率和相位误差.通过计算机仿真研究、湖试试验,验证了该系统在复杂的水声信道中具有较强的抗多径能力、抗多普勒能力,能实现低误码率通信,具有较好的有效性和鲁棒性.     

Sparse synthetic aperture radar imaging with optimized azimuthal aperture

To counter the problem of acquiring and processing huge amounts of data for synthetic aperture radar(SAR)using traditional sampling techniques,a method for sparse SAR imaging with an optimized azimuthal aperture is presented.The equivalence of an azimuthal match filter and synthetic array beamforming is shown so that optimization of the azimuthal sparse aperture can be converted to optimization of synthetic array beamforming.The azimuthal sparse aperture,which is composed of a middle aperture and symmetrical bilateral apertures,can be obtained by optimization algorithms(density weighting and simulated annealing algorithms,respectively).Furthermore,sparse imaging of spectrum analysis SAR based on the optimized sparse aperture is achieved by padding zeros at null samplings and using a non-uniform Taylor window.Compared with traditional sampling,this method has the advantages of reducing the amount of sampling and alleviating the computational burden with acceptable image quality.Unlike periodic sparse sampling,the proposed method exhibits no image ghosts.The results obtained from airborne measurements demonstrate the effectiveness and superiority of the proposed method.