RLL码的计算机辅助设计

本文着重讨论计算机辅助设计RLL码的具体实现问题.该过程首先根据RLL码两个参数d,k确定一个编码率p/q,然后构造出RLL码的高阶状态转换-输出符号矩阵并求相应的近似特征向量.最后通过状态分裂和状态归并过程,即可得到一个满足d,k约束的编码输出表.其中状态转换-输出符号矩阵为实现计算机辅助设计RLL码提供了有效的数据结构,而且要优化RLL码编码器,就必须有选择地进行状态分裂.     

ANALYSIS ON ROOM TEMPERATURE TENSILE STRENGTH OF δ-Al_2O_3, FIBER / Al-12Si COMPOSITE

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度δｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τＰ确定复合材料的ＲＯＭ预测曲线，应首先判断σｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论。     

碳纤维表面处理对铝电解用硼化钛阴极涂层性能的影响

硼化钛阴极涂层是铝电解用可润湿性阴极材料中的一种，具有优良的抗钠渗透性和对铝液润湿性，可以有效地延长铝电解槽寿命。碳纤维是硼化钛涂层材料的增强剂之一．对硼化钛阴极涂层的性能影响很大。本文研究了不同工艺的液相碳纤维表面氧化处理法对硼化钛阴极涂层抗拉强度和粘接强度的影响。采用PTIR检测碳纤维处理后表面含氧基团的变化，寻找影响硼化钛阴极涂层性能的原因，从而达到最有效地提高TiB2阴极涂层抗拉强度和粘接强度的目的。结果表明，采用工艺(1)(10％HNO3，80℃、恒温5min．超声波、5min)对碳纤维进行表面处理最合理，处理后碳纤维表面含氧基团的含量最高．用其制备硼化钛阴极涂层的抗拉强度、粘接强度最大。     

Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

Mycological and physical parameters for selecting suitable packaging material for pre- and post-irradiation storage of cereal grains in Ghana

Owing to the rough warehouse handling of storage sacks in tropical areas in Africa, a suitable storage sack should not support de novo growth of fungal spores because this would reduce the tensile strength of the packaging material and act as a springboard for infecting grain contents. This paper reports the effect of activity of saprophytic fungi on the tensile strength of jute and woven polypropylene sacks. New woven polypropylene sacks carried lower levels of fungal spores (1.3×10¹ cfu/72 cm²) than jute sacks (3.0×10³ cfu/72 cm²). The natural mould penetration and growth was examined on sections (4×5 cm) of both jute and woven polypropylene after previous incubation at relative humidities of 55, 60, 65, 70, 75, 80, 90 and 95% for 10 weeks by placing them on Sabouraud's Agar. There was a significant difference (P = 0.05 level of significance) between the higher penetration of mould growth on jute sacks and that obtained on woven polypropylene sacks. Saprophytic fungi (Aspergillus candidus, A. flavus, A. fumigatus, A. niger, A. japonicus, A. parasiticus, A. ustus, Fusarium oxysporium, F. moniliforme, Penicillium verucosum var. cyclopium, Rhizopus oryzae and Trichoderma viride) isolated from jute sacks reduced tensile strength, measured by an Instron Model 1026, by 50–75% after 10 weeks at 90% R.H. Same fungal species on woven polypropylene sacks did not alter the tensile strength. Woven polypropylene sacks did not absorb moisture whilst the moisture content of jute sacks increased by 5.3–6.0% in 10 weeks at 90% R.H. with concomitant increase in mould and yeast counts by 1–2 log cycles. Evidence is presented to show that there was a positive correlation between the final mycoflora on jute sacks and loss in tensile strength. No correlation, however, was found between the total aerobic bacteria on jute sacks and the concomitant reduction in tensile strength. Fungi therefore play a major role in the reduction of tensile strength of jute sacks. Sterilization by gamma irradiation (8.0 kGy) of jute and woven polypropylene sacks did not affect their intrinsic tensile strength. Woven polypropylene sacks therefore have many microbiological and physical advantages over the traditional jute sacks to merit their use for grain storage in tropical areas like Ghana.     

Studies on chitin 3—effect of coagulants and annealing on the preparation and the properties of chitin membrane

Chitin membrane was prepared by casting a N,N-dimethyl acetamide, N-methyl 2-pyrrolidone and lithium chloride (DMA-NMP-LiCl)solution of chitin and coagulating with several media. The effect of the coagulants on membrane formation was studied. 2-Propanol was found to be more favourable than methanol, ethanol, acetone and mixtures of 2-propanol and water. The membrane obtained in 2-propanol was subjected to annealing. Annealing made the membrane dense and strong. The tensile strength of the membrane annealed at 145°C for 2hr was about twice that of an unannealed membrane. The solute permeability of the annealed membranes was lower than that of the original one. These phenomena could be clearly interpreted in terms of crystallinity.     

拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。     

Residue curve maps for reactive distillation systems with liquid-phase splitting

A model has been developed to study the effects of chemical kinetics on the residue curve maps (RCM) for reactive distillation systems with liquid phase splitting. In the model, chemical reaction can occur in both or only one of the two liquid phases. The heating policy V/V₀=H/H₀ is applied so that the kinetic effect can be described by a single parameter, the Damköhler number Da. The effects of reaction kinetics on pseudohomogeneous and heterogeneous mixtures have been compared. The properties of their RCMs are the same outside, but are fully different inside the liquid-liquid (L-L) region if they have different chemical equilibrium curves. Inside the L-L region, the chemical equilibrium curve coincides to a unique reactive liquid-liquid tie line in case that the pseudohomogeneous chemical equilibrium curve intersects with the L-L envelope. When the reaction occurs in only one of the two liquid phases, the residue curves inside the L-L region are strongly affected by the L-L envelope, especially at high Da. In the present paper, first an illustrative arbitrary reaction system, and then the reaction of cyclohexene with water to cyclohexanol are analysed with respect to their RCMs.     

Non‐reflecting artificial boundaries for transient scalar wave propagation in a two‐dimensional infinite homogeneous layer

This paper presents an exact non‐reflecting boundary condition for dealing with transient scalar wave propagation problems in a two‐dimensional infinite homogeneous layer. In order to model the complicated geometry and material properties in the near field, two vertical artificial boundaries are considered in the infinite layer so as to truncate the infinite domain into a finite domain. This treatment requires the appropriate boundary conditions, which are often referred to as the artificial boundary conditions, to be applied on the truncated boundaries. Since the infinite extension direction is different for these two truncated vertical boundaries, namely one extends toward x →∞ and another extends toward x→‐ ∞, the non‐reflecting boundary condition needs to be derived on these two boundaries. Applying the variable separation method to the wave equation results in a reduction in spatial variables by one. The reduced wave equation, which is a time‐dependent partial differential equation with only one spatial variable, can be further changed into a linear first‐order ordinary differential equation by using both the operator splitting method and the modal radiation function concept simultaneously. As a result, the non‐reflecting artificial boundary condition can be obtained by solving the ordinary differential equation whose stability is ensured. Some numerical examples have demonstrated that the non‐reflecting boundary condition is of high accuracy in dealing with scalar wave propagation problems in infinite and semi‐infinite media. Copyright © 2003 John Wiley & Sons, Ltd.     

THE TENSILE STRENGTH OF WATER IN DEPRESSION TANK

This paper presents the data of tensile strength of water in depression tank whichwere measured by small venturi during cavitation investigation of a series of real project models.These measurements show that in depression tank water has slight tensile strength in case of highvacuum.But it influences the incipient cavitation number.In tests we also studied the influenceof tensile strength on scale effect of cavitation models.