Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

Optimal size,hydraulic retention time and volatile solids loading rate of biogas unit using water hyacinth

With a view to evaluate the effects of hydraulic retention time and volatile solids loading rate on methane production using water hyacinth, experiments were conducted in a 160 dm³ capacity, well-mixed continuous digestion unit at ambient temperature. The optimal design of biogas plant using water hyacinth was elucidated, to provide a unit giving a maximum methane yield of 0.16 nm³ kg^?1 volatile solids added, which was 60% greater than the conventional plant using cowdung. The calculations of optimal design factors were based on reactor size, hydraulic retention time and volatile solids loading rate; considerations were made of capital cost, running costs and operational revenue.     

铁路站段用交流不间断电源供电系统

结合铁路站段的特点 ,介绍了一种交流不间断电源供电系统 ,能够很好的解决其供电问题。     

Lower bound limit analysis using non‐linear programming

This paper describes a new formulation, based on linear finite elements and non‐linear programming, for computing rigorous lower bounds in 1, 2 and 3 dimensions. The resulting optimization problem is typically very large and highly sparse and is solved using a fast quasi‐Newton method whose iteration count is largely independent of the mesh refinement. For two‐dimensional applications, the new formulation is shown to be vastly superior to an equivalent formulation that is based on a linearized yield surface and linear programming. Although it has been developed primarily for geotechnical applications, the method can be used for a wide range of plasticity problems including those with inhomogeneous materials, complex loading, and complicated geometry. Copyright © 2002 John Wiley & Sons, Ltd.     

大型水轮发电机组励磁变压器参数及绝缘方式的选择--由三峡机组励磁系统投运引起的思考

结合三峡机组励磁系统的调试及投运经验,对大型水电机组静止自励系统选型中存在的一些关键性技术课题进行分析与论证,期望得出的结论有助于在大型水轮发电机组励磁系统参数选择和在提高机组运行安全、可靠性方面提供有益的借鉴。文中提出的励磁系统设计新理念仅代表个人的观点。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

基于加载算法的室内无线信道OFDM接收机的性能

本文研究了无线局域网中使信号频谱得到优化的一种简单OFDM子载波加载算法。此算法基于边缘自适应（Margin Adaptive）加载准则及其在室内无线信道上的性能。     

Two-stage fatigue loading of woven carbon fibre reinforced laminates

A brief review of the models used to predict the cumulative fatigue damage in FRP composites is presented. Two‐stage fatigue loading of a [0/90,± 45₂,0/90]_s quasi‐ isotropic woven carbon fibre/epoxy resin laminate was evaluated at stress ratio R = 0.05 and the failure mechanisms investigated using x‐radiography after each loading stage. The results are presented in terms of fatigue strength and damage growth and are compared with those in the literature. A low‐to‐high loading sequence is more damaging than a high‐to‐low one and the Palmgren‐Miner linear damage rule may no longer be valid for this kind of material, as previously reported.     

UV法测定聚甲基丙烯酸酯纳米粒中胰岛素的包封率

建立一种简便易行的测定聚甲基丙烯酸酯胰岛素纳米粒中游离胰岛素含量方法.用Nanosep OD100C33超滤膜分离纳米粒和游离药物,在276 nm处测定药物的吸光度,建立胰岛素含量测定方法,并对线性、回收率、精密度等指标进行考察,最后测定各种胰岛素和载体比例混合的纳米粒的包封率.结果发现,该超滤膜能较好地分离纳米粒和游离的药物,在0.11～1.10 u/mL范围内,药物在276 nm的吸光度和浓度存在良好的线性关系(r=0.999 8),线性方程为A=0.868 8C-0.001 6,高、中、低3种浓度的回收率和精密度良好.该方法操作简单、结果可靠,可用于胰岛素纳米粒中药物包封率的测定.     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.