A method for observing the three-dimensional morphologies of inclusions in steel

A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water,acetone,and HC1 (volume ratio,45∶45∶10...     

造粒机模板与切粒刀对聚乙烯颗粒质量的影响

通过多年来对聚乙烯造粒系统的调查研究及现场实践，确认了聚乙烯产品质量的影响因素。选择了造粒模板与切粒刀之间的最佳匹配。     

浅谈丁基胶垫与气门嘴的粘合

本文介绍了丁基橡胶垫与铜制气门嘴粘合的有关问题，并提供了解决方法。     

Corrosion-resistant analogue of Hadfield steel

The concept of alloying austenitic steels with carbon + nitrogen is used for the development of a corrosion-resistant austenitic CrMn steel having an impact wear resistance close to that of the Hadfield steel. A higher stabilization of the austenitic phase by C + N, as compared to carbon or nitrogen alone, is substantiated by ab initio calculation of the electron structure, measurements of the concentration of free electrons and calculations of the phase equilibrium. Based on these results, the compositions (mass%) Cr18Mn18C0.34N0.61 and Cr18Mn18C0.49N0.58 were melted and tested along with Hadfield steel Mn12C1.2. Mechanical tests have shown that, as compared to the Hadfield steel, the experimental steels possess a higher strength, plasticity, hardness and the same resistance to impact wear. TEM studies of the surface layer after impact treatment revealed a mixture of the amorphous phase, nanocrystals and fine-twinned austenite. At the same time, using Mössbauer spectroscopy of conversion electrons, the ferromagnetic ordering was found in the surface layer of up to 10 μm in depth, which is the sign of the strain-induced martensitic phase. The hypothesis of a transition from the low-spin to the high-spin state of the iron atoms within the thin twins in austenite was proposed in order to interpret the discrepancy between TEM and Mössbauer studies. Potentiodynamic measurements and immersion tests show that the CrMnCN steels possess a significantly higher pitting potential and resistance to general corrosion in comparison with Hadfield steel.     

多元回归分析在电热式平板硫化机热板温度场中的应用

分析电热平板硫化机热板温差大的主要影响因素,重点研究热源分布情况对温差的影响.以400×400电热平板硫化机为例,应用多元回归的二次响应曲面模型及其子模型,对热源间距(电热管间距)与热板表面最大温差之间的函数关系进行预测,检验并分析预测结果(拟合曲线)的可靠程度,从而得出较合理的数学模型,即完整二次响应曲面模型.此模型可为工程设计提供参考依据.     

Formation of CaO-TiO2-MgO-Al2O3 dual phase inclusion in Ti stabilized stainless steel

The formation of CaO-TiO2-MgO-Al2O3 dual phase inclusion in 321 stainless steel was investigated in the laboratory. The result indicated that the condition for the formation of CaO-TiO2-MgO-Al2O3 in 321 steel is [Ca]〉0.001wt%, [Ti]〉0.1wt%, and [A1]〉0.01wt%. The mechanism is the following： Al2O3 inclusion turns into CaO-Al2O3 after Ca-Si wire is fed into the molten steel; [Mg] is then obtained by reducing MgO in slag or crucible wall by [Al] and [Ti]; finally CaO-Al2O3 inclusion is changed into CaO-TiO2-MgO-Al2O3 by the reaction with [Mg], [Ti], and [O] in the molten steel simultaneously.