Optically tuned superconductive-dielectric resonators with whispering-gallery modes

An analytical method is presented for calculating the resonant frequency andQ-factor of a superconducting dielectric disk resonator operating in millimeter-wave regime with whispering-gallery mode. Resonant frequency shift due to the optical generation of quasi-particles in superconducting film is investigated as a function of photon flux. An optically tunable resonant frequency of about 500 MHz is estimated, and good agreement is found between numerical results and experimental ones.     

提高炮采工作面块煤率的爆破技术

通过小规模爆破试验，用线性回归方法对块煤进行筛分分析，指出影响炮采工作面块煤率的因素是炸药性能、装药结构、爆破参数、起爆顺序、时间间隔等。     

Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

Drying of Prone to Twist Boards in a Pre-Twisted Position

A method to minimize twist has been investigated; i.e., drying the boards in a pre-twisted position. It has been found that Norway spruce boards can be deformed toward straightness by this method. The force exerted by a board on its holders during drying in a pre-twisted position has been measured. When the variation in torsional stiffness as a function of temperature and moisture content is accounted for, it is found that a creep deformation of the board occurs both during the drying phase and the cooling phase. In addition to mechano-sorptive creep, a deformation released by a change in temperature also seems to occur.     

Electron microscopic observations and DNA chain fragmentation studies on apoptosis in bone tumor cells induced by ~(153)Sm-EDTMP

ＥｌｅｃｔｒｏｎｍｉｃｒｏｓｃｏｐｉｃｏｂｓｅｒｖａｔｉｏｎｓａｎｄＤＮＡｃｈａｉｎｆｒａｇｍｅｎｔａｔｉｏｎｓｔｕｄｉｅｓｏｎａｐｏｐｔｏｓｉｓｉｎｂｏｎｅｔｕｍｏｒｃｅｌｓｉｎｄｕｃｅｄｂｙ１５３ＳｍＥＤＴＭＰＺｈｕＳｈｏｕＰｅｎｇ，Ｘｉａ...     

高梯度加速管的束流传输

对不同能量、不同质量数、不同初始条件的入射束和有无空间电荷效应的离子束流在高梯度加速管中的传输进行了计算，并讨论了一些影响加速管聚焦作用的主要因素，计算结果与实际情况相符。     

High temperature low cycle fatigue

Fatigue at high temperature is a complex phenomenon as it is influenced by a number of time-dependent processes which become important at elevated temperatures. These processes include creep, oxidation, phase instabilities and dynamic strain ageing (DSA), acting either independently or synergistically influence fatigue behaviour, often lowering the fatigue life. Current design approaches employ linear summation of fatigue and creep damage with suitable factors on permissible damage to take care of uncertainties in interaction between cyclic and time-dependent processes. It is, therefore, important to develop a deeper understanding of the processes that occur during high temperature fatigue so that realistic life predictions could be made. Results on the high temperature fatigue behaviour of austenitic stainless steels, ferritic steels and nickel base alloys are presented here. The important mechanisms of interaction of high temperature time-dependent processes with fatigue under various conditions are discussed in detail. Emphasis is placed on cyclic stress response, fatigue life, deformation substructure and fracture behaviour. This is followed by a review of important life prediction techniques under combined creep-fatigue loading conditions. Life prediction techniques considered here include linear damage summation, strain range partitioning, ductility exhaustion approach, frequency modified and frequency separation methods, techniques based on hysteresis energy and damage rate models, and methods based on crack-cavitation interation models.     

Proposed modification to the CIECAM02 colour appearance model to include the simultaneous contrast effects

A modified CIECAM02 colour appearance model, named CIECAM02‐m2, is proposed to enable CIECAM02 to predict the simultaneous contrast effect. The structure of the CIECAM02‐m2 is a development from CIECAM02, and contains two different procedures for modifying the reference white; one is for lightness and the other is for hue. The model was tested using a data set accumulated in this study and the LUTCHI data. The CV values for three colour attributes between predictions and experimental data were used to evaluate the accuracy of the model. The low CV values obtained show the performance of the CIECAM02‐m2 model to predict the simultaneous contrast effect satisfactorily. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 121 – 129, 2007     

A new alloy design concept for austenitic stainless steel with tungsten modification for bipolar plate application in PEMFC

The feasibility of a new alloy design concept utilizing the principle of ‘tungsten bronze effect’ is critically evaluated for the development of metallic bipolar plates for proton exchange membrane fuel cell (PEMFC). An austenitic stainless steel (ASS) is modified with W and La to improve the stability of the passive film in an acidic environment as well as to reduce the contact resistance by the tungsten bronze effect. The experimental ASS containing W and La was evaluated in a simulated PEMFC environment of H₃PO₄ and H₂SO₄ solutions at 80 °C, and the electrical property was evaluated by performing a contact resistance test. The test results show that the ASS modified with W and La has good passive film stability for corrosion resistance and low contact resistance. The X-ray photoelectron spectroscopy (XPS) analysis clearly suggests the possibility of the tungsten bronze effect from the change in valency state of W⁶⁺ to W⁵⁺ in the passive film formed on the modified ASS. The feasibility of a new alloy design concept utilizing the ‘tungsten bronze effect’ is well demonstrated; however, more study is highly required for the development of metallic bipolar plates of PEMFC.     

EC与~（99m）Tc－GH之间的配体交换反应动力学研究

实验表明，ＥＣ浓度与配体交换反应速度常数无关，体系的ｐＨ值对速度常数和９９ｍＴｃ－ＥＣ的标记率影响较大。测定并计算了不同ｐＨ值的交换反应速度常数。结果表明，为保证用配体交换法制备９９ｍｃ－ＥＣ时９９ｍｃ－ＥＣ的标记率大于９０％，体系的ｐＨ值必须≥８。