电镀塑料制品对结构设计及成形工艺的要求

为保证电镀塑料制品的质量,提出了符合电镀要求的塑料制品设计原则,并且指出在注塑成形时,对塑料经过充分干燥,采用较高的注塑温度,较低的注射压力和较慢的注射速度,是使镀层获得良好结合强度的先决条件。     

EDA9033A在分布式风机性能测试系统中的应用

针对以单片机为核心的风机性能测试系统存在稳定性差、抗干扰能力差、精度低等问题,开发了以PLC为核心、采用互感式采集模块EDA9033A采集风机电参数的分布式风机性能测试系统,给出了该风机性能测试系统的结构,详细介绍了EDA9033A的硬件及软件设计。实际应用表明,EDA9033A采集的风机电参数结果稳定、快速、准确。     

2HL055恒流二极管参数测试

2HL055是贵州博越公司生产的恒流二极管,该类器件恒定电流大,极限电压低,可以直接驱动负载,但器件形成实验室成品后,没有进行过参数测试,其基本参数范围不能确定。文章拟通过试验,进一步测试2HL055器件的基本参数,并确定部分参数的测试方法。     

Stochastic differential equations driven by a Wiener process and fractional Brownian motion: Convergence in Besov space with respect to a parameter

A stochastic differential equation involving both a Wiener process and fractional Brownian motion, with nonhomogeneous coefficients and random initial condition, is considered. The coefficients and initial condition depend on a parameter. The assumptions on the coefficients and the initial condition supplying continuous dependence of the solution on a parameter, with respect to the Besov space norm, are established.     

Controlling the diffusionless Lorenz equations with periodic parametric perturbation

Diffusionless Lorenz equations (DLE) are a simple one-parameter version of the well-known Lorenz model, which was obtained in the limit of high Rayleigh and Prandtl numbers, physically corresponding to diffusionless convection. A simple control method is presented to control chaos by using periodic parameter perturbation in DLE. By using the generalized Melnikov method, the parameter conditions could be obtained to guide the controlled DLE to a low-periodic motion. Moreover, the existence conditions of periodic orbits and homoclinic orbits in the system are given. Some results of the numerical simulation are also explained clearly by a rigorous analysis.     

Output feedback robust MPC for LPV system with polytopic model parametric uncertainty and bounded disturbance

The output feedback robust model predictive control (MPC), for the linear parameter varying (LPV) system with norm-bounded disturbance, is addressed, where the model parametric matrices are only known to be bounded within a polytope. The previous techniques of norm-bounding technique, quadratic boundedness (QB), dynamic output feedback, and ellipsoid (true-state bound; TSB) refreshment formula for guaranteeing recursive feasibility, are fused into the newly proposed approaches. In the notion of QB, the full Lyapunov matrix is applied for the first time in this context. The single-step dynamic output feedback robust MPC, where the infinite-horizon control moves are parameterised as a dynamic output feedback law, is the main topic of this paper, while the multi-step method is also suggested. In order to strictly guarantee the physical constraints, the outer bound of the true state replaces the true state itself, so tightness of this bound has a major effect on the control performance. In order to tighten the TSB, a procedure for refreshing the real-time ellipsoid based on that of the last sampling instant is given. This paper is conclusive for the past results and far-reaching for the future researches. Two benchmark examples are given to show the effectiveness of the novel results.     

合成氨工艺参数优化技术开发及应用

以氨净值为响应值,影响响应值的17个过程参数为变量,经逐步回归选入触媒温度左3,触媒温度左4,循环CH_4%,H/N,NH_3%(进口)5个过程参数建立预测方程,并根据该方程对响应值的拟合结果和误差分布对样本进行分类。在此基础上,采取图形显示技术和统计分析的方法对分类样本集的过程参数进行比对分析,由此获取优类信息制订优化的工艺参数方案,经仿真验证后用于指导合成氨装置的生产试验。试验结果与试验前的对照期比较,氨净值均值由13.86提高到14.54,吨氨气耗减少15.9887m~3,吨氨电耗减少15.8kWh,节能效益十分明显     

金属表面环氧漆漆膜拉伸剪切强度的测定

借鉴国标胶粘剂拉伸剪切强度测定方法测定了阳极、阴极环氧电泳漆与环氧涂料在底材为铝合金及钢材上漆膜的拉伸剪切强度，在铝件及钢铁件表面上阳极电泳漆漆膜的拉伸剪切强度为11．60MPa及17．91MPa，阴极电泳漆漆膜分别为17．60MPa及23．20MPa，喷涂环氧漆膜为7．93MPa 及13．40MPa，并介绍了测定试验中的实际操作经验和技术细节。     

低密度、高强度DG型高变催化剂的研制

本文叙述了一种适合大型氨厂使用的、堆密度低到1.25 kg·L^-1、还原态侧压强度高达350 N·cm^-1以上、本体含硫＜500 ppm(wt)、低温活性好的高温变换催化剂的研制开发过程 还介绍了催化剂制备工艺特点和工业试用效果。