井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.     

Use of X-ray computed microtomography to understand why gels reduce relative permeability to water more than that to oil

X-ray computed microtomography (XMT) was used to investigate why gels reduce relative permeability to water more than that to oil in strongly water-wet Berea sandstone. XMT allows saturation differences to be monitored for individual pores during various stages of oil, water, and gelant flooding. The method also characterizes distributions of pore size, aspect ratio, and coordination number for the porous media. We studied a Cr(III) acetate–HPAM gel that reduced permeability to water (at S_or) by a factor 80–90 times more than that to oil (at S_wr). In Berea, the gel caused disproportionate permeability reduction by trapping substantial volumes of oil that remained immobile during water flooding (i.e., 43.5% S_or before gel placement versus 78.7% S_or after gel placement). With this high trapped oil saturation, water was forced to flow through narrow films, through the smallest pores, and through the gel itself. In contrast, during oil flooding, oil pathways remained relatively free from constriction by the gel.     

Requirements engineering in health care: the example of chemotherapy planning in paediatric oncology

Health care is characterized by highly complex processes of patient care that require unusual amount of communication between different health care professionals of different institutions. Sub-optimal processes can significantly impact on the patient’s health, increase the consumption of services and resources and in severe cases can lead to the patient death. For these reasons, requirements engineering for the development of information technology in health care is a complex process as well: without constant and rigorous evaluation, the impact of new systems on the quality of care is unknown and it is possible that badly designed systems significantly harm patients. To overcome these limitations, we present and discuss an approach to requirements engineering that we applied for the development of applications for chemotherapy planning in paediatric oncology. Chemotherapy planning in paediatric oncology is complex and time-consuming and errors must be avoided by all means. In the multi-hospital/multi-trial-centre environment of paediatric oncology, it is especially difficult and time-consuming to analyse requirements. Our approach combines a grounded theory approach with evolutionary prototyping based on the constant development and refinement of a generic domain model, in this case a domain model for chemotherapy planning in paediatric oncology. The prototypes were introduced in medical centres and final results show that the developed generic domain model is adequate.     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

Review of Alterations of Consciousness: An Empirical Analysis for Social Scientists.

Reviews the book by Baruss (see record 2003-02669-000), which reviews the experimental and phenomenological research on alterations of consciousness, ranging from sleep and dreaming to mystical and near-death experience. The reviewer suggests there is a clear agenda announced by the book's subtitle, "An Empirical Analysis for Social Scientists." In the view of Baruss, all too often in states of consciousness research a preoccupation with theory has kept investigators from full engagement with the actual data. The book provides readable and at times appropriately controversial discussions of empirical literature on dreaming and lucid dreams, daydreaming and fantasy proneness, hypnosis, dissociative identity disorder, shamanism and possession states, psychedelic drug research, parapsychology, trance-chanelling and mediumship, the alien abduction syndrome, classical mystical experience, out-of-body and near-death experiences, and recent attempts by MacDonald and others to assess individual differences in spirituality through multifactor questionnaires. However, the reviewer believes that the breadth of coverage of both recent and past research is too often highly selective, and that the author's rejection of theory is both questionable in itself and more illusion than reality. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

火工品压药机装配误差的研究

针对军用雷管生产线中压药机结构,分别用极值法和概率法对压药机冲子和雷管的配合精度,进行了装配尺寸链的描述和计算,并对所得的结果进行了比较。     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

δ－Al_2O_3纤维／Al－12Si复合材料室温拉伸强度分析

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度σ＇ｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τｉ．确定复合材料的ＲＯＭ预测曲线，应首先判断σ＇ｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论     

Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.