Residual Stress Evolution in Repair Welds

Abstract: The aim of this paper is to study the influence of the repair procedure on the evolution of residual stress distribution in butt welds. C-Mn steel coupon plates of 11 mm thickness were prepared, subjected to stress relief heat treatment and welded with two beads, using the gas metal arc welding process. After the deposition of two weld beads, two successive repair welds were made on the middle length of the second bead. Longitudinal and transverse residual stresses were measured in the vicinity of the weld, after deposition of the two weld beads and after each repair weld. Residual stress evaluation was conducted using an X-ray diffraction method. The repair welds caused a decrease in magnitude of the initial longitudinal residual welding stresses, and an increase of the transverse residual stress magnitude, in tension at points within the repair length, and in compression at points outside the repair length.     

转子叶片在非均匀来流条件下的流体激振特性

该文通过研究得出非均匀来流对转子叶片流体激振的三个重要特征 :非均匀来流相对于转子叶片的非定常流中主频分量是产生叶片动应力的决定因素 ;非均匀来流的非均匀度 (相当于非定常流的波幅 )大小和叶片流体激振的动应力大小成正比 ;转子叶片流体的定常压力水平与叶片动应力的水平密切相关。图 4表 2     

固井水泥环缺陷对套管强度影响仿真分析

固井水泥环质量对套管的强度影响很大。建立了水泥环缺少1／12的井筒平面应变有限元模型，通过对固井水泥环缺陷引起的套管应力变化进行仿真模拟分析，得出无内压下套管的最大径向位移是水泥环完整时的3．9倍，水泥环的缺少导致Mises应力集中系数为2．0，套管外壁的最大塑性应变达到0．0152，定量分析固井质量对套管强度的影响，为热采井套管损坏提供一些定量数据。     

复合地基中优化设计参数的方法

本文给出了复合地基应力比置换率设计的优化方法,讨论了复合地基中应力比的基本概念和影响因素,可供工程应用时参考。     

Calculation of fatigue limits of case-hardened specimens with consideration of mean stresses and residual stresses

 The strength of case-hardened parts under cyclic loading can be determined in an experimental manner, but this can produce a large amount of costs due to the expenditure of material and testing time. Therefore, a calculation method is developed, that strongly reduces the number of experiments. The presented model is based on Weibull's weakest-link concept and allows to compute the survival probability of a case-hardened part which is loaded close to the fatigue limit. The essential quantities in this model are the distribution of Vicker's hardness of the material, the exponents of the Weibull distribution of the volume and the surface, the residual stress state, the surface roughness and the surface oxidation depth. By integrating the survival probabilities of the surface and the volume, the survival probability of the entire specimen or part can be calculated, which allows to compute the fatigue limit. The necessary parameters have to be determined from reference specimens. The model is successfully examined by comparing experimental and calculated results of smooth and notched case-hardened specimens under alternating torsion, rotating bending, repeated tension and tension-compression. Received 20 August 2001 / Accepted 11 November 2001     

影响塑料模压制件内应力的因素分析

主要讨论了造成塑料模压制件内应力的主要因素,包括制件造型设计不合理、模具设计不合理、成型工艺条件不正确等,并针对不同情况给出了相应的解决办法     

封隔器胶筒接触应力分布有限元计算

利用ANSYS软件对3种封隔器胶筒的接触应力进行了有限元计算，得到了接触应力沿胶筒轴向的分布情况。比较不同结构封隔器胶筒在相同条件下的接触应力分布，可知新型封隔器胶筒在高压下接触应力分布更为均匀合理，具有较好的应用前景。     

超薄氧化层中的中性陷阱对隧穿电流的影响和应变诱导漏电流

用数值分析的方法讨论了中性陷阱对超薄场效应晶体管(MOSFET )隧穿电流的影响.中性陷阱引起势垒的变化在二氧化硅的导带中形成一个方形的势阱.对于不同的势垒变化,计算了电子隧穿氧化层厚度为4nm的超薄金属氧化物半导体结构的电流.结果表明,中性陷阱对隧穿电流的影响不能被忽略,中性陷阱的存在使隧穿电流增加,并且通过这个简单的模型能够理解应变诱导漏电流的产生机制.