COMPRESSION FATIGUE CRACK GROWTH BEHAVIOUR OF AN ALUMINIUM ALLOY: EFFECT OF OVERLOADING

Abstract— The behaviour of fatigue cracks in an Al-alloy under cyclic compression, either with or without overloads, was studied. For constant-amplitude compressive cycling, a non-catastrophic (saturation) character of the fatigue crack behaviour was confirmed, with the final depth of a crack depending on the applied load level. Single (tensile or compressive) intermittent overloads were shown to re-activate a previously arrested crack while reversed (tensile—compressive or compressive—tensile) ones were also shown to maintain continual fatigue crack extension under otherwise fully compressive cycling.     

氧化铝陶瓷缺口件循环疲劳及断裂机理

用实验方法研究了Ａｌ＿２Ｏ＿３陶瓷缺口试件在循环载荷作用下的疲劳寿命。结果表明，缺口导致的应力集中效应显著降低了循环疲劳寿命；若用缺口根部最大应力为应力水平，则不同缺口半径陶瓷试件具有相同疲劳断裂规律，说明陶瓷材料的疲劳集中系数和理论应力集中系数相同。本文还分析讨论了陶瓷材料的循环疲劳寿命表达式和循环疲劳断裂机理。     

冲击能传感器的研究与分析

本文分析并推导了应力波在弹性体中传播时,质点的运动速度、压力、位移及应力载波的聚流的形成与表达式.利用得到的公式描述了冲击能传感器的工作机理.给出了某风动工具的测试结果.     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

具有细小组织的高强度和高延性钢管的开发

介绍了日本川崎制铁公司技术研究所开发出的电焊钢管采用热张力减径工艺的特性 ,及这种钢管的高强度、高延性等基本特性。用这种钢管制造的汽车零部件 ,经弯曲、冲击和疲劳特性等实验 ,证明具有良好的机械加工性能 ,是制造汽车用零部件的优良材料。     

板式塔中无伸缩型受液槽的改进

对板式塔中的受液槽进行了改进，将无伸缩型改性伸缩型，避免了漏液，提高了常压塔的分离效果。     

湿硫化氢环境下的球罐腐蚀状况分析

在湿硫化氢环境下 ,尤其储存介质中的硫化氢含量超标时 ,很容易对储存容器壳体 (含焊缝和母材 )造成硫化氢应力腐蚀或氢鼓包。作者较仔细分析了 1 0 0 0m3 丙烯球罐产生硫化氢应力腐蚀开裂和40 0m3 LPG球罐产生氢鼓包的原因。提出了此类设备在设计选材、设备制造、施工安装和使用维护等环节应注意的问题。     

地壳应力场和密度场资料在油气检测中的应用

依据卫星轨道摄动测量结果反演的地壳区域构造应力场和密度场资料，可圈定油气区域构造圈闭和储集油气的低密度层。计算绘制了闽江口扇形洲区域构造应力场和密度卫星遥感图，图上显示出东海近海闽浙中拗陷含油气带与温东丽水油气构造带相接，敖江口官岭与闽江口川石储岛沥青苗等迹象都在此范围内，在闽江口扇形洲东部沿海沙泥沉积区，邻区东海宽长带深厚海沙软泥沉积区及本区北部罗源湾，用大地电磁CSAMT检测到1000－3000m深度范围内的低阻率地层，与本区卫星遥感图图低密度场相符。     

复相材料的循环变形行为

对三种组织状态的F-M复相钢进行了对称和非对称循环加载条件下的形变研究.结果表明,双相钢的循环变形行为,不仅与组织中位错组态的演变过程有关,同时也受循环载荷大小、类型以及加载方式所影响.分析表明,双相钢的循环硬化、软化行为主要受控于两个基本过程,即循环变形时位错组态演变的物理过程和相间分载应力的转嫁、相间残余应力变化的力学过程.     

高层建筑物整体形变的GPS监测

利用GPS观测数据 ,进行高层建筑物的整体形变监测模型和方法的研究是一项重要的工作。本文针对高层建筑物监测环境及其对监测快速、高精度的要求 ,尝试性地提出了高层建筑物整体形变模型 ,说明了模型应用要求和特点 ,详细给出了针对该模型的GPS监测方案 ,并用实例说明了模型和方案的实施步骤 ,实例分析得出了有益结论。