Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

蒸发冷凝法中气体压强和蒸发温度对粒子大小的影响

在Ｎ＿２气氛中，用蒸发冷凝法，制备了Ｓｎ细微粒和Ｆｅ及Ｆｅ－４７（ｗｔ）％Ｎｉ合金超细微粒。分别用ＳＥＭ和ＴＥＭ，直接观测粒子大小及其分布。结果表明，平均粒径不是随Ｎ＿２气压强增加单调上升，而是在某一压强Ｐ＿（ｍａｘ）下，出现最大值。随蒸发温度提高，Ｐ＿（ｍａｘ）值迅速增大。粒子大小及其分布与粒子生长机制密切相关。对粒子凝聚生长条件进行了简要讨论。     

改造加热炉系统 提高加热炉热效率

分析了重整装置加热炉热效率低的原因，介绍了提高加热炉热效率采取的几项措施。     

葛洲坝电站2号水轮机转轮室中环修复

针对葛洲坝电站2号机组运行中出现转轮室中环损坏的现象,设计制造出转轮室现场机加工的大型专用机床,在修复改造过程中,解决了一系列技术难题,改造后技术指标均达到理想水平,为电站机组现场修复技术积累了宝贵经验.     

三模式氡测量刻度装置的研制

为满足实验室对一般氡测量仪器的刻度需要,设计了能够实现在脉冲模式、恒定模式和连续模式三种模式下自动控制、自动监测的氡测量刻度装置,并对装置进行了稳定性和可靠性试验。试验结果表明,该装置可为氡及其子体的研究以及其测量仪器的标定提供一个可调节、具有稳定氡浓度的环境。     

A graded diameter and oriented nanorod–thin film structure for solar cell application: a device proposal

This paper presents a device proposal based on a junction between an absorbing semiconductor nanorod structure and another window semiconductor layer for solar cell application. The possibility of band gap tuning by varying the diameter of the nanorods along the length, higher absorption coefficient at nanodimensions, the presence of a strong electrical field at the nanorod-window semiconductor nanojunctions and the carrier confinement in lateral direction are expected to result in enhanced absorption and collection efficiency in the proposed device. Process steps, feasibility, technological tasks needed for the realization of the proposed structure and the novelty of the present structure in comparison to the already reported nanostructured solar cells are also discussed.     

圆锥孔径测量方法与误差分析

圆锥孔径的测量往往比较困难、且精度较低。提出长度测量仪器与环规配合使用,应 用比较测量的方法检测圆锥孔的直径。通过计算和分析可以得出,当被测圆锥孔径不大于180 mm 时,其测量不确定度可小于1.84 μm。给出了测量方法和不确定度计算公式供操作时参考。     

钻井岩屑粒径分布规律的研究

钻井振动筛是固控系统的重要分离设备,其主要任务是清除钻井液中直径大于74μm的固相颗粒。对辽河油田7口井深0～3500m的钻井岩屑进行了实地取样,分析了岩样颗粒直径大于74μm的粒径分布特征。分析结果表明,钻井岩屑具有明显的片状特征,颗粒的粒径分布主要与地层岩性和破岩工具有关,随着井深的变化,其岩样粒径分布呈现出幂分布、2分布和瑞利分布等3组典型规律。给出了岩屑颗粒的概率直径;建议在筛面颗粒运动特性研究、筛网工作载荷的计算和激振方式的选择中,应考虑岩屑颗粒片状特性的影响。     

温度,压力对漂移室气体增益的影响

研究了温度及气体压力对漂移室（工作于正比区）气体放大倍数的影响，温度和气体压力的变化范围分别是５￣４０℃及９０￣１０５ｋＰａ。用实验数据拟合得到了函数关系并测量了几种饱和度下函数中的参数值。     

基于移动锚节点的无线传感器网络圆心定位

文章提出了一种利用无线传感器网络无线信号接收强度（RSSI）和移动锚节点轨迹来获得待定节点位置的算法。该算法在有多个可移动锚节点的情况下,定位将会更加高效。在定位阶段,通过RSSI测得锚节点到待定节点的距离,并利用三个以上移动锚节点的坐标（包括三个）来求解圆的方程,计算出待定节点的位置。