Studies on chitin 3—effect of coagulants and annealing on the preparation and the properties of chitin membrane

Chitin membrane was prepared by casting a N,N-dimethyl acetamide, N-methyl 2-pyrrolidone and lithium chloride (DMA-NMP-LiCl)solution of chitin and coagulating with several media. The effect of the coagulants on membrane formation was studied. 2-Propanol was found to be more favourable than methanol, ethanol, acetone and mixtures of 2-propanol and water. The membrane obtained in 2-propanol was subjected to annealing. Annealing made the membrane dense and strong. The tensile strength of the membrane annealed at 145°C for 2hr was about twice that of an unannealed membrane. The solute permeability of the annealed membranes was lower than that of the original one. These phenomena could be clearly interpreted in terms of crystallinity.     

拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。     

Formation and investigation of epoxy intumescent compositions modified by active additives

Results are reported of research on intumescent composites based on epoxy resin cross‐linked with polyethylene polyamine and containing ammonium polyphosphate and such modifying additives as calcium borate, manganese dioxide, nickel, and chromium, containing tubulenes as gas‐formers and carbonization stimulators. The changes in composition and physicochemical properties of modified compositions under conditions of heat and fire were investigated by X‐ray photo‐electron spectroscopy, atomic force microscopy, and local force spectroscopy. Ammonium polyphosphate mainly stimulates carbonization processes on the inner surface of a bubble being formed during foam coke formation. The introduction of metal‐containing tubulenes leads to the formation of fire‐retardant and low flammability‐compositions with high coke and carbon structures content. The use of calcium borate in the compositions considerably increases the strength of foam coke being formed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1477–1483, 2002     

软土中的基坑支护工程实例分析

武汉某地下车库基坑处于深厚淤泥中 ,采用排桩 +土层锚杆支护与放坡 +网喷分段支护方式 ,本文根据现场地质、地形条件 ,对本工程支护过程中支护桩与土体变形作了具体分析。     

延长分米波电视发射管使用寿命的探讨（上）

文章从原理上讨论了影响分米波电视发射管寿命的若干因素。并提出了若干延长寿命的建议：（１）正确的灯丝加热方法是行之有效的措施，经验证明：过分强调降低灯丝电压往往得到相反的效果。（２）必须有良好的冷却方式。（３）通过对帘栅电路的分析，说明对此电路必须作很好的处理以消除故障和防止寄生振荡。     

A force modulation study on crystallization process in ferroelectric vinylidene fluoride and trifluoroethylene copolymer films

This paper introduces the Force Modulation technique to the study of crystallization process in ferroelectric vinylidene fluoride and trifluoroethylene copolymer films. Using this technique we have successfully visualized ferroelectric crystalline domains and observed that these ferroelectric domains grow out from amorphous phase, unite into strip-like structures, and finally congregate into a union. Force Modulation can weaken the influence of topography on imaging of ferroelectric domains, and reveal more details, which are difficult to be observed in topographical image.     

Optimizing the Vacuum Heat-Treatment of Hot-Work Tool Steels by Linear Elastic Fracture Mechanics

Linear elastic fracture mechanics was used to optimize the vacuum heat-treatment procedures for conventional hot-work AISI H11 tool steel. The fracture toughness was determined with non-standard, circumferentially notched and fatigue-precracked tensile-test specimens. The fracture-testing method is sensitive to changes caused by variations in the microstructure resulting from the austenitizing and tempering temperatures as well as the homogeneity of the material itself. The combined tempering diagram- Rockwell-C hardness, Fracture toughness K_Ic, Tempering temperature was used for the choice of the vacuum heat-treatment parameters necessary to obtain the best properties for a given application with respect to the investigated steel.     

THE TENSILE STRENGTH OF WATER IN DEPRESSION TANK

This paper presents the data of tensile strength of water in depression tank whichwere measured by small venturi during cavitation investigation of a series of real project models.These measurements show that in depression tank water has slight tensile strength in case of highvacuum.But it influences the incipient cavitation number.In tests we also studied the influenceof tensile strength on scale effect of cavitation models.     

钢管机械扩径工艺研究

介绍了大口径直缝焊管机械扩径的优点，原理及扩径力的计算，找出影响扩径力及扩径头寿命的因素。     

适用于稠油开采的游梁式抽油机设计分析

在稠油开采中,抽油杆在液体中运动时,所受到的摩擦阻尼力很大,有时高达几十千牛。上冲程时,该力有加大悬点载荷的作用;下冲程时,该力使抽油杆下行困难,甚至悬点载荷为零。为了开采稠油,必须根据其特点设计适应的游梁式抽油机。文章分析了稠油用抽油机的受力特点,提出了该类抽油机的设计要求。