Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

电力变压器动稳定破坏的分析和对策

对大型电力变压器绕组在变压器发生外部短路时所受的辐向力和轴向力进行了分析和计算，比较了国内外不同的计算方法和得出的不同结果。     

具有细小组织的高强度和高延性钢管的开发

介绍了日本川崎制铁公司技术研究所开发出的电焊钢管采用热张力减径工艺的特性 ,及这种钢管的高强度、高延性等基本特性。用这种钢管制造的汽车零部件 ,经弯曲、冲击和疲劳特性等实验 ,证明具有良好的机械加工性能 ,是制造汽车用零部件的优良材料。     

碳纤维增强水泥/混凝土材料力学性能的若干研究

本文通过对水泥基体掺入碳纤维进行研究，得出了复合体抗压强度、劈拉强度与碳纤维掺量的关系。同时文中还利用聚丙烯腈纤维作对比研究，得出目前碳纤维作为增强体的优缺点，为碳纤维增强水泥基复合材料的推广应用提供更多的实验依据。     

HA型粘结剂性能评判的研究

冷固结球团直接还原工艺成功的关键因素之一是成型粘结剂的选用。粘结剂性能评判 ,传统的方法是通过考查球团矿的机械强度来说明粘结剂性能的优劣 ,步骤繁锁。经过试验研究 ,本文提出了用粘度大小来评判粘结剂性能的直接方法并从理论上进行了论证。对于 HA型复合粘结剂 ,在六速旋转粘度计上测量 ,50 g复合粘结剂的粘度若大于或等于 6.5× 1 0 -3 Pa·s,表示粘结剂性能较好 ,能满足铁精矿冷固球团直接还原工艺的要求 ;若小于或等于 3.0× 1 0 -3 Pa· s,则表示该粘结剂性能较差。     

Incoloy 800H合金的应用和性能分析

通过对耐热耐蚀合金Incoloy 80 0H的性能分析 ,指出它与普通奥氏体不锈钢相比具有较优的抗氧化性能、耐蚀性和高温蠕变强度。针对催化裂化装置同轴式沉降再生器内部所用Incoloy 80 0H焊件易出现裂纹的问题进行分析 ,认为在施焊过程中由于合金凝固时有低熔点金属或化合物的液态膜残留在晶界区 ,该合金具有高的焊接热裂纹敏感性 ,若焊材选择不当 ,焊丝填充不充分、缺少保护气等将导致晶间裂纹产生。提出了该合金采用TIG焊接防止热裂纹产生的措施。     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。     

Structural acrylic adhesives for the sheet steel fabrication industries

Recent developments in rubber-toughened structural acrylic adhesives now offer sheet steel fabricators the opportunity to replace conventional metal fastening techniques such as spot welding with lower cost, durable, more versatile structural adhesive bonding. These developments, in particular much improved ability to bond oily/waxy surfaces common to the motor car industry and improved retention of fracture toughness after exposure to paint stoving temperatures, are discussed in this paper.     

管材拉伸模具定径区摩擦力的探讨

管材拉伸时把模具定径区看作准塑区，利用塑性条件，研究定径区摩擦力对拉伸力的影响，并对计算公式进行探讨。证明管材空拉（减径不减壁）时摩擦力影响可忽略不计，但减径、减壁拉伸同时进行时，定径区摩擦力对拉伸力的影响就必须考虑。     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.