油田单井平均日产油量经济极限确定方法

从f(n,t)曲线的研究出发,得到了求解油田单井平均日产油量经济极限值的数学方程式,介绍了用曲线交汇法求解的过程,分析了油田月递减余率和原油销售价是影响油田单井平均日产油量经济极限的主要因素。该方法在油田开发调整方案的编制和油田开发规划部署工作中将起到一定的作用。     

Review of Qualité de vie et drogues. Place aux jeunes.

Reviews the book, Qualité de vie et drogues. Place aux jeunes (1986). In this volume, the author shares his initiatives in the plan of therapeutic and preventive intervention. This book discusses drug use and quality of life in young people. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

N.m.r. study of the ferroelectric phase transition in a 7030mol% copolymer of vinylidene fluoride (VF2) and trifluoroethylene (TrFE)

Nuclear magnetic resonance (n.m.r.) studies of ¹⁹F nuclei in a $\text{70}\text{30}\text{mol}\text{\%}$ random copolymer of vinylidene fluoride and trifluoroethylene were performed at 9.14 MHz and 20.0 MHz. The free induction decays (FIDs) were analysed in terms of two T₂ components attributed to the amorphous and crystalline portions of the polymer. The changes in crystallinity as well as the effects of the ferroelectric transition were observed during cycles of heating and cooling between 20°C and 140°C. The crystalline component of the FID lengthens by a factor of 2 at 100°C on heating and decreases by this factor at 60°C on cooling, thus exhibiting the thermal hysteresis of this ferroelectric transition. The spin-lattice relaxation was also investigated. From measurements at 9.14 MHz the observed longitudinal relaxation time T₁ appears to be dominated by the dynamics of the amorphous phase and exhibits no anomaly through the phase transition. However, from measurements at 20 MHz, well defined minima of T₁ were observed, which are associated with the ferroelectric transition (especially after repeated annealing of the samples). Results are discussed in terms of the crystalline phase structure, which appears dynamically disordered above the ferroelectric phase transition. An analogy is considered with the plastic phase transitions encountered in molecular crystals.     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.     

Treatment of Humic Waters By Ozone

Two different generators for ozone were tested, a traditional electrical discharge generator and a generator based upon UV–irradiation of air at 150–180 nm. It was demonstrated that the traditional generator gave slightly higher reductions in levels of color for equivalent ozone dosages. Both gases affected the molecular weight distribution in the way that the bigger molecules were broken down to smaller ones. No significant difference between the molecular weight reduction efficiency of the gases was found.     

HHD型核子秤电离室物理性能检测

HHD型核子秤电离室已成功地使用于HCS型核子秤.对它的各种物理性能指标进行了检测,各项性能指标都达到了设计要求。     

An automatic method for controlling the centre of gravity of a model

In many applications the location of the centre of gravity of a mechanical part is an important factor that a designer must consider. If it is not in a desired location, a part might not work properly, e.g. unbalanced force might be generated in a rotational part. After a part is modeled, its centre of gravity cannot be altered unless its external shape or internal mass distribution is changed. However, the external shape is usually constrained by other design considerations. In this paper, an algorithm is proposed for controlling the centre of gravity of a hollowed part. Using this algorithm, the location of the centre of gravity of a part is controlled by changing its internal mass distribution.     

Thermophysical properties data: Government-university-industry cooperation in multidisciplinary research

Historical developments regarding the realization of the importance of reliable thermophysical properties data in engineering applications are presented. The events leading to the establishment of the Symposium on Thermophysical Properties in 1959 and the accomplishments of the symposia series since then are discussed. Contributions of the National Bureau of Standards to the thermophysical properties field are described.Welcoming address presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.