Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

现代通信产品静电防护技术导则

本导则提出了电子通信设备机房内静电荷的产生根源及静电放电对其设备正常运行的影响机理，提出机房内环境装修的静电防护措施及静电防护操作等，从而达到有效地控制静电荷的，确保电子通信设备安全可靠运行。本导则适用于以集成电路为核心的现代通信设备机房的设计和管理。     

钨系延期药预点火反应机理研究

通过程控升温模拟点火条件，根据ＤＳＣ图谱分析，找出主要反应区的温度范围。研究结果表明，钨系延期药预点火反应是一个真正的固－固反应。     

Geochemical approach to the Bou Hadjar hydrothermal system (NE Algeria)

The Bou Hadjar low-temperature hydrothermal system is located in northeast Algeria. The four main thermal springs that are the subject of the study emerge ith temperatures between 32 and 60°C from allochthonous formations. The reservoir temperature has been estimated from chemical compositions by utilizing simultaneously the silica, gas and sulfate-water oxygen isotope geothermometers, fluid-mineral equilibrium calculations, and a mixing model. According to these thermometric methods, the most probable subsurface temperature is in the range 75–106°C. The mixing model suggests a temperature of 125°C for the parent water.     

Transport properties of 1,1-difluoroethane (R152a)

Based on reliable. carefully selected data sets. equations for the thermal conductivity and the viscosity of the refrigerant R 112a are presented. They are valid at temperatures from 240 to 440 K, pressures up to 20 MPa. and densities up to 1050 kg · m^–3. including the critical region.     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

Flow dynamics or ‘quaking’ in gravity discharge from silos

This paper reviews the characteristics of pulsating or cyclic flow of bulk solids during gravity discharge in bins and silos. The dynamic load phenomenon is often referred to as “silo quaking” and is influenced by various factors related to the type of flow pattern developed in the bin and the flow properties of the bulk material. Of particular relevance is the influence of ‘slip-stick’ during shear flow, and the velocity at critical sections in the silo during discharge. An overview of recent and current research on this subject is presented.     

Measurement of the thermal diffusivity of thin films on substrate by the photoacoustic method

Measurements of the thermal diffusivity of thin films on substrate have been performed by the photoacoustic method. In order to examine the method we have built a new apparatus and proposed (1) a system calibration procedure using optically and thermally thick reference samples and (2) a data analysis procedure based on the RG (Rosencwaig and Gersho) theory. As a result of using a transparent photoacoustic cell, the systematic errors which are caused by stray light have been reduced. With this apparatus, measurements have been performed on platinum, titanium, and stainless steel (SUS304) thin foils (thickness form 50 to 100 µm) with three different liquid backing materials (water, glycerol, and ethyl alcohol). The reproducibility was within ±7% regardless of film thickness and substrate materials.