“三软”煤层综放面特殊情况下支架拆除及沿空留巷

超化煤矿21091(西)综采工作面因出水造成工作面停产,在不超前15 m铺金属网的情况下进行支架拆除,并把原工作面留做炮采面切巷。根据实际情况制定了施工方案,并介绍了实施情况。     

铁水鱼雷罐的检测方案研究

论文介绍了一种针对铁水鱼雷罐车铁水液位检测的较为可行的低成本方案。采用车上间接称重、远红外非接触传输信号方式，解决了对移动铁水罐车进行实时监测的难题。     

埋地管道三层PE外覆盖层及其检测方法研究

文章介绍了埋地管道三层PE外覆盖层系统的构造参数和性能特点,论述了两种用于埋地钢质管道外覆盖层状况检测的方法,一种是多频管中电流法,另一种是DCVG/CIPS组合检测技术。分别介绍了两种方法的工作原理、操作方法和设备,并结合工程实例进行了说明。这些方法和设备可分别或同时用于管道不开挖检测防腐层破损点的位置以及漏点大小。     

Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model

1 Introduction During injection moulding, the rheological response of polymer melts is generally non-Newtonian and nonisothermal with the position of the moving flow front. Because of these inherent factors, it is difficult to analyze the filling process. Therefore, simplifications usually are used. For example, in middle-plane technique and dual domain technique [1], because the most injection molded parts have the characteristic of being thin but generally of complex shape, the Hele-Shaw …     

用RAFA方法定量解析芳烃混合物的EEM

本文介绍了降秩因子分析(RAFA)方法,它是从一个多组分混合物中直接定量计算其中某一组分,而不必知道其它组分的物种及含量的一种定量分析的数学方法。它适用于双线性的数据。本实验首先将荧光分光光度计与外接计算机相连,以获得样品的激发-发射矩阵(EEM),再用RAFA方法对蒽、萘、菲、芘、芴、(艹屈)六种标样的一至五组分的混合物进行定量分析,获得满意的结果。     

纤维共晶生长界面前沿三维扩散场解析

修正Ｊａｃｋｓｏｎ和Ｈｕｎｔ关于在垂直生长方向截面上溶质扩散各向同性假设，求解三维Ｌａｐｏｌａｃｅ方程，获得纤维共晶生长界面前沿三维稳态扩散场，并证明Ｊａｃｋｓｏｎ和Ｈｕｎｔ的二维模型是实际生长的二维简化和一阶近似，并用丁二腈（ＳＣＮ）一梓脑（ＣＡＭ）纤维共晶系统计算生长界面前沿溶质分布。     

浅谈做好螺丝湾水电站施工质量,工期,投资控制的几项措施

螺丝湾水电站作为云南省电力局（ 集团公司） 、迪庆州、省投资公司三方合资建设的电站，是迪庆藏族自治州自建国以来投资最大的一个建设项目，它的建成，开创了滇西北水电资源多方合资开发的先例，有其特殊的经济和政治意义。本文结合螺丝湾水电站建设的实际情况，论述了在市场经济条件下做好螺丝湾电站建设中“三控制”的几项措施     

TVD有限体积法在二维超音速流计算中的应用

将具有二阶精度的ＴＶＤ有限体积法推广应用到三维无粘流的计算．提出三维流场计算使用的计算网格的生成方法．最后计算了三维纯头体超音速绕流，并和相应文献的结果进行了比较，结果令人满意     

Selective partial oxidation of light paraffins with hydrogen peroxide on thin-layer supported Nafion-H catalysts

Thin-layer carbon supported Nafion-H catalysts were found to be active and highly selective (S>98%) for the partial oxidation of C₁-C₃ alkanes, in a three phase catalytic membrane reactor (3PCMR), under mild conditions and in the presence of H₂O₂. The influences of the catalyst teflon loading and H₂O₂ concentration on the reaction rate have been evaluated. A reaction pathway, based on the electrophilic hydroxylation of the C-H bond of alkanes with protonated hydrogen peroxide (H₃O ₂ ⁺ ), is discussed.     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002