Calculation of fatigue limits of case-hardened specimens with consideration of mean stresses and residual stresses

 The strength of case-hardened parts under cyclic loading can be determined in an experimental manner, but this can produce a large amount of costs due to the expenditure of material and testing time. Therefore, a calculation method is developed, that strongly reduces the number of experiments. The presented model is based on Weibull's weakest-link concept and allows to compute the survival probability of a case-hardened part which is loaded close to the fatigue limit. The essential quantities in this model are the distribution of Vicker's hardness of the material, the exponents of the Weibull distribution of the volume and the surface, the residual stress state, the surface roughness and the surface oxidation depth. By integrating the survival probabilities of the surface and the volume, the survival probability of the entire specimen or part can be calculated, which allows to compute the fatigue limit. The necessary parameters have to be determined from reference specimens. The model is successfully examined by comparing experimental and calculated results of smooth and notched case-hardened specimens under alternating torsion, rotating bending, repeated tension and tension-compression. Received 20 August 2001 / Accepted 11 November 2001     

热流体喷射变形机理与喷嘴结构

高速短程纺技术能生产三维卷曲短纤维,该技术的关键之一是热流体喷射装置。本文介绍了热流体喷射装置的演变与特点及它的加工机理和某些已应用的实际装置。     

平衡纵剖面数值试验及其对防洪的影响研究

本文采用一维非恒定流非均匀沙的水沙数学模型，以长江中游螺山汉口河段为背景，进行了根化数值模拟试验，分析了该概化河段平衡纵剖面的变化规律及其与上游来水来沙条件的关系，并和相应的理论公式进行了比较。在此基础上，对水沙条件发生较在变化时的平衡纵比降以及带来的对长江中下游防洪的影响进行了分析。     

Resilient metal spring network silicone-matrix composite for separable interconnections

Resilient metal spring silicone-matrix conducting composites for separable interconnections in electronics were fabricated by the impregnation of silicone into a preform comprising randomly oriented C-shaped Cu-Be springs and a small proportion of Sn-Pb solder, which served to connect the springs at some of their intersections. Composites containing 6.1-9.8 vol.% total filler exhibited volume electrical resistivity 0.5-1.0 mΩ.cm and contact resistivity (with copper) 11-17 mΩ.cm². A compressive stress of about 30 kPa was needed for the low contact resistivity to be reached. The volume 17-26% and the contact resistivity increased by 5% after heating in air at 130-150°C for seven days. Composites containing <9 vol.% total filler showed no stress relaxation for seven days at 6.0% strain.     

Impurity Distribution Behavior in Caprolactam Extraction with Environmentally Benign Mixed Solvents

In a previous study a solvent mixture of heptane containing 40 mass % heptanol was selected as an alternative in the industrial extraction of caprolactam to replace benzene, toluene, or chlorinated hydrocarbons. This work reports the equilibrium distribution ratio of caprolactam and four model impurities of organic nature, namely, cyclohexanone, aniline, n‐methylcaprolactam, and cyclohexane‐carboxamide, comparing the mixed solvents with toluene as a reference. The resulting phase equilibria were interpreted using the equilibrium stage model. Based on these calculations it was found that, compared to toluene, the co‐extracted fraction of cyclohexanone and aniline was higher, that of n‐methylcaprolactam was comparable, and that of cyclohexane‐carboxamide was lower using the mixed solvent. Overall, the mixed solvent reduced the fraction of co‐extracted impurities by almost 10 %.     

从限额设计谈投资控制

文章根据设计阶段投资控制的现状及存在问题,提出只有在设计行业全面推行限额设计,深化设计阶段的投资控制工作,才能从根本上体现全过程投资控制的理念,提高投资控制效果,节约建设工程总投资。     

间苯二酚溶剂萃取液液相平衡研究

测定了“醋酸正丁酯-间苯二酚(溶质)-盐水(含0.2质量分率NaCl)”三元系在24℃、101.33kPa下的液液相平衡数据并给出了三角相图,用Hand公式对相平衡数据进行了关联,获得了可供工业连续萃取过程设计使用的关联式。本研究将醋酸正丁酯和正丁醇作为溶剂萃取间苯二酚进行了对比,并指出:醋酸正丁酯优于正丁醇。     

Modelling of the extraction equilibrium of zinc from chloride solutions with tri-n-octylphosphine oxide

The extraction of zinc from chloride solutions with tri-n-octylphosphine oxide (TOPO) dissolved in benzene has been thermodynamically studied based on the law of mass action. A model employing the simplified Pitzer equations for stoichiometric activity coefficient estimations is found to be effective for the explanation and prediction of the distribution data, and the thermodynamic extraction constant is determined as log K_et = 5.16 ± 0.11 at 20°C.     

基于PRO/E三维管道轨迹专用检具的设计

介绍使用该软件组件设计模块中的高级工具———切除 (CutOut)功能设计高精度三维轨迹管道零件检具的方法 ,该方法具有高效和精密等特点。