二(二甲苯基)丙烷合成工艺的研究

二氯丙烷(DCP)与二甲苯在混合金属氯化物催化剂(HD90)作用下合成二(二甲苯基)丙烷,生产过程简单,产品收率高。在60—80℃的温度下,二甲苯与二氯丙烷摩尔比为6∶1,HD用量50克/摩尔DCP的条件下反应5—6小时,二(二甲苯基)丙烷的收率可达88％以上。     

Natural zeolite utilisation in pollution control: A review of applications to metals' effluents

This paper assesses the potential of natural zeolite utilization as a low-cost ion-exchange and sorbent material in pollution control and recovery of metals. The improvement of the purity of natural zeolites coupled with their chemical modification capabilities in order to provide specific properties may provide a cost-effective alternative for the treatment of heavy metal contaminated soil and water. The application of natural zeolites in industrial pollution control is becoming important and the level of technical effort is increasingly expanding. The extent of application is unlikely to be related solely to their low cost, but also to improved properties and performance characteristics, which will advance the practical implementation of natural zeolites' technology.     

含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。     

热采水平井整体开发草13块砂砾岩薄层特稠油

热采水平井技术是科学有效开发稠油油藏的重要手段。以胜利油田草13块为例，系统论述了利用热采水平井整体开发具有边底水的砂砾岩薄层特稠油油藏的开发程序和研究方法。在油蒇精细描述的基础上，通过热采筛选、产能评价、直井和水平井数值模拟、开发方式优化及指标预测等油藏工程研究技术方法，综合论证了利用热采水平井整体开发草13块的必要性和可行性，总结了砂砾岩薄层特稠油油藏水平井油藏工程设计中应遵循的原则，并在生产实践中见到明显效果，为胜利油田其它区块和类似油田的开发提供了借鉴和指导。     

稠油油藏的注汽量预测

利用HCZ预测模型，可对已开发油田的年产量和累计产量进行全程预测，并且在实际应用中取得了较好的预测结果。本文结合稠油田的实际情况，推导出HXZ预测模型在热采中注汽参数的预测公式。结合曙光油田曙1－7－5块的开发数据进行了预测，效果较好。     

松香及其衍生物在浮选分离中的应用

介绍了松香的来源、化学组成及理化性质；讨论了松香及其衍生物在非硫化物矿浮选分离、有色金属离子的浮选分离以及从水溶液中浮选分离有机物等方面的应用情况。     

Schottky barrier heights of contact metals to p-type ZnSe

Schottky barrier heights (SBHs) of a variety of metals (In, Cd, Nb, Ti, W, Cu, Ag, Au, Ni, Pt, and Se) contacting to p-ZnSe grown by a molecular beam epitaxy method were determined by analyzing capacitance-voltage (C-V) and/or current density-voltage (J-V) curves. The SBH values of the Au and Ni contacts were determined from intersections of straight lines of the C⁻²-V curves to be 1.23 and 1.13 eV, respectively. The J-V calculations provided a large SBH value of 1.2 ± 0.1 eV for a variety of metals, indicating that the Fermi-level could be pinned at the contact interface. Reduction of the SBH values to a level lower than 0.4 eV and/or increase of doping concentrations to a level higher than 10²⁰ cm⁻³ are essential to obtain an ohmic contact with contact resistivity of around 10⁻³ Ω·cm².     

Effects of crack size and weld metal mismatch on the has cleavage toughness of wide plates

The heat affect zone (HAZ) is in many cases considered to be the most critical part of a weldment. In this paper, the effect of crack size and weld metal mismatch on the HAZ cleavage toughness of wide plate specimens with X-groove has been investigated by the J-Q-M theories and a simple micromechanism for cleavage fracture. Two crack sizes have been studied (a/w = 0.1 and 0.3). In the analyses, the HAZ yield strength is assumed to be higher than the base metal. For each crack size, weld metal local overmatch and local evenmatch with respect to the HAZ are considered. For a given global strain, the results indicate that weld metal overmatch and evenmatch yield the same crack tip loading in terms of J-integral for a/w = 0.3. For a/w = 0.1, overmatch gives lower crack tip loading than evenmatch. For a given crack tip loading, weld metal local evenmatch in general results in less effective crack tip loading than the overmatch. Overmatch is detrimental to HAZ toughness, but this detrimental effect becomes less significant when the crack size decreases.     

特超稠油污水回掺降粘集输工艺

通过对河南古城油田BQ10区特超稠油乳状液的室内试验分析,指出该种乳状液的实际相突变点为68%左右,当相浓度Φ≥68%时,以W/O型为主的乳状液突变为以O/W型为主的乳状液.乳状液变型后,原油与管道内壁之间的摩擦以及原油之间的摩擦转变为水与管道内壁及水与水之间的摩擦,从而大幅度降低其粘度和摩阻损失;通过对古城BQ10区特超稠油区块单元内部污水回掺降粘集输的现场试验,证明与室内试验分析得出的结论相符合,说明区块单元污水回掺不同于常规的掺热水,也不同于掺联合站处理过的净化污水,它优于单井掺稀油.最后指出该工艺可有效地降低井站回压,方便生产管理,降低开采成本,提高采油效率和经济效益,具有低耗节能的优点.     

圆锥形零件冲压变形与成形载荷的分析

由于悬空侧壁部分的变形状态是圆锥形零件成形的关键，而径向拉应力是实现悬空部分成形的必要条件，同时也是该部分冲压成形成败的关键为此，经力学分析得出了侧壁部分径向拉应力的解析式和造成圆锥形零件破裂的最大径向拉应力的计算式。同时分析了圆锥形零件的成形载荷。