Comparison of mass transfer efficiency in horizontal rotating packed beds and rotating biological contactors

In this study, the mass transfer efficiencies of a novel horizontal rotating packed (h‐RPB) bed and the conventional disc‐type rotating biological contactor (RBC) were studied at four speeds and seven submergences. Pall rings of two different sizes (25, 38 mm), superintalox saddles and a wiremesh spiral bundle were used as packings in the h‐RPB. Volumetric gas–liquid mass transfer coefficients were determined by unsteady state absorption of atmospheric oxygen in de‐aerated water. Power consumption per unit liquid volume has been found for all geometries tested. The oxygen transfer efficiency values for the h‐RPB were found to be 2–5 kg kWh^?1 and for the disc RBC were found to be 1–2 kg kWh^?1. The performance of the h‐RPB was also compared with other gas–liquid contactors such as surface aerators. The study proves that the h‐RPB is a energy efficient alternative to conventional contactors. Copyright © 2005 Society of Chemical Industry     

纳米NiO粉体的制备及其表征

采用溶胶转化－凝胶法制备了纳米级NiO粉体。Ni(OH)2粉体的TG－DSC分析表明：在升温速率为10℃/min的条件下，粉体在489K时开始显著分解，626K时分解完毕。X－射线衍射分析表明：分解产物为纯净的NiO2。NiO粉体的化学成分分析表明：其纯度高于国家标准。TEM电镜分析表明：NiO粉体呈单分散的球形或棒状颗粒。对NiO粉体的热敏性能有待进一步研究。     

碘量法测铜中物质性质和分析操作

本文讨论了碘量法测定铜量中一些有关物质的特性,以及这些性质对分析条件和操作的要求。     

Mass transfer kinetics of neodymium(III) extraction by calix[4]arene carboxylic acid using a constant interfacial area cell with laminar flow

BACKGROUND: Thermodynamics and kinetics data are both important to explain the extraction property. In order to develop a novel separation technology superior to current extraction systems, many promising extractants have been developed including calixarene carboxylic acids. The extraction thermodynamics behavior of calix[4]arene carboxylic acids has been reported extensively. In this study, the mass transfer kinetics of neodymium(III) and the interfacial behavior of calix[4]arene carboxylic acid were investigated. RESULTS: The rate constant (K_ao) becomes constant when the stirring speed was controlled between 250 rpm and 400 rpm. The activation energy (E_a) was calculated to be 21·41 kJ mol^?1 or 88·17 kJ mol^?1 (dependent on temperature) from the slope of log K_ao against 1000/T. The linear relationship between the specific area and the extraction rate is the characteristic of an interfacial reaction control. The minimum bulk concentration of the extractant necessary to saturate the interface (C_min) is lower than 4·19 × 10^?4 mol L^?1. CONCLUSION: The effect of stirring speed, temperature, and species concentration on the extraction rate demonstrates that the extraction regime depends on the extraction conditions. The chemical reaction control governs the extraction regime at temperatures below 303 K and a mixed control regime occurs when the temperature is between 303 K and 318 K. The probable locale for the chemical reaction is at the liquid–liquid interface and the rate equation is deduced to be: ? d[Nd³⁺]_(a)/dt = k_f[Nd³⁺]_(a)[H₄A]_(o)^0·727[H⁺]_(a)^?0·978. The rate‐controlling step was suggested by the analysis of the experimental results. Copyright © 2008 Society of Chemical Industry     

棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。     

NUMERICAL ANALYSIS AND EXPERI- MENT OF UNSTEADY THERMAL FIELD OF ROTOR PLATE FOR EDDY CURRENT RETARDER

The physical model based on heat transfer theory and virtual boundary method for analyzing unsteady thermal field of rotor plate for eddy current retarder used in automobile is established and boundary conditions are also defined. The finite element governing equation is derived by Galerkin method. The time differential item is discrete based on Galerkin format that is stable at any condition. And a new style of varying time step method is used in iteration process. The thermal field on the rotor plate at the radial and axle directions is analyzed and varying temperature at appointed points on two side-surfaces is measured. The testing and analytical data are uniform approximately. Finite element method can be used for estimating thermal field of the rotor plate at initial design stage of eddy current retarder.     

Symmetric BEM formulations for 2-D steady-state and transit potential problems

This paper presents a new concept for symmetric boundary element method (SBEM) applicable to 2-D steady-state and transit potential problems. Two kinds of SBEM formulations are derived. Symmetry is obtained simply through matrix manipulation, and no hypersingularity appears. Therefore, SBEM is much easier than the traditional symmetric Galerkin BEM. Compared with the traditional asymmetric BEM, the present SBEM can reduce the computational cost for time domain problems only. However, when applied to BEM/FEM coupling procedure, SBEM can reduce the computational cost for both steady-state and time domain problems. Three numerical examples are included to illustrate the effectiveness and accuracy of the present formulations.     

Linear Algebra Considerations for the Multi-Threaded Simulation of Mechanical Systems

A solution method suitable for the multi-threaded simulation ofmechanical systems represented in Cartesian coordinates isproposed and analyzed. In a state-space framework for thesolution of the Differential Algebraic Equations (DAE) ofMultibody Dynamics, the position/velocity stabilization and theacceleration computation are based on iterative solvers applied toequivalent reduced problems. The most in-depth computationalaspect analyzed is the preconditioning, i.e., the direct solutionof the reduced systems. Provided a topology index reduction is first applied to the model, the effort for the direct solution of the reduced systems is shown to be of order O(N _J ), where N _J is the number of joints in the model. The recurring theme of thepaper is the central role that the topology of the mechanicalsystem plays in the overall performance of the numericalsimulation. Based on the topology of the model, parallelcomputational threads can be established to start in the equationformulation and continue through the iterative numericalalgorithms employed for the numerical solution. Task schedulingthese parallel threads is expected to redeem real-time performancefor certain classes of complex applications.