预应变下焊接接头冲击韧度及韧-脆转变的分析

以常用建筑结构钢(16Mn和Q235B)为研究对象，通过不同温度下的夏比冲击试验研究预应变对其母材和焊缝冲击性能的影响。结果表明，材料在预应变下无论是母材还是焊缝夏比冲击韧度均有所降低，韧一脆转变温度有所提高。5％预应变后的16Mn母材和焊缝其韧一脆转变温度均低于室温(20℃)，因此仍可在室温下安全使用；Q235B钢室温下冲击韧度较16Mn钢低，且预应变对母材影响更大，和未经预应变冲击值相比，降低了三倍有余。可以看出，Q235B钢的抗震性能较16Mn差。研究发现：为建立客观的材料韧度指标和进行更有效的安全分析时，预应变也应该作为一个考虑因素。     

STRAIN INDUCED STRUCTURAL TRANSITION OF INTERFACES AND TWINS IN A HOT－DEFORMED DUAL－PHASE TIAL ALLOY

ＳＴＲＡＩＮＩＮＤＵＣＥＤＳＴＲＵＣＴＵＲＡＬＴＲＡＮＳＩＴＩＯＮＯＦＩＮＴＥＲＦＡＣＥＳＡＮＤＴＷＩＮＳＩＮＡＨＯＴ－ＤＥＦＯＲＭＥＤＤＵＡＬ－ＰＨＡＳＥＴＩＡＬＡＬＬＯＹＣＨＥＮＧｕｏＦｉａｎｇ；ＷＡＮＧＪｉｎｇｕｏ；ＺＨＡＮＧＬｉｃｈｕｎａｎｄ...     

V形件弯曲凹模最小深度的确定

该文指出了目前广泛使用的经验查表法确定V形件弯曲凹模深度的不合理性，分析了凹模斜壁的作用及其与圆角半径的相互关系，提出了凹模最小的深度的概念和计算公式。     

仪表视窗注射模设计

分析了电器仪表视窗的工艺性,介绍了电器仪表视窗注射模具的结构设计,并对采用公差带来计算成型零件尺寸的方法进行了初步的探讨,可以在一定程度上预测模具的使用寿命。     

高温W/Re流口复合界面上的扩散层

W/Re流口在高温下使用时,复合界面处会发生反应扩散而形成一个由固溶体(W),双相σ,双相x,固溶体(Re)4个相组成的过渡层。并作出了不同反应扩散时间的浓度分布曲线,及浓度突变形成的双相区,从而确定了各相成份组成。对经反应扩散后的复合界面进行微观观察发现x相、σ相内有许多间隔式微裂纹,据此认为高温下W/Re流口失效原因是使用过程中上述两x,σ相内裂纹扩散,熔体渗入所致。     

不等厚板过渡削薄对接焊缝的超声波探伤

不等厚板经过渡削薄处理后的对接焊缝,由于厚度的不均匀,射线穿透时的衰减不一样,对射线检测带来很大的麻烦。常用的超声波探伤方法在定位和定级方面比较困难,本文给出利用现在先进的数字式超声波探伤仪进行准确探伤的方法。     

Recent Advances in Conjugated Transition Metal-containing Polymers and Materials

Metal-containing conjugated oligomers and polymers are reviewed, focusing on the work carried out by the author and coworkers since 1995. The synthesis of model systems, electropolymerizable monomers and polymer films are discussed, along with the electronic and spectroscopic properties of these systems. The application of phosphino-oligothiophene ligands as an entry to conjugated metallopolymers is described.     

严重非均质油藏高渗条带的识别方法

胡状集油田属于严重非均质油藏,在注水开发后表现为油井见效快、含水上升快,并且很快在注采井间形成高渗条带,影响开发效果。如何对高渗条带识别,成为改善严重非均质油藏开发效果的关键。本文通过沉积微相法、测井评价方法、示踪剂监测分析法、动态分析法等多种方法,开展对高渗条带识别的研究,为下步措施安排提供了可靠的调整依据。     

ATTRITION IN THE BUBBLING ZONE OF A STEADY-STATE FLUIDIZED BED

This paper describes the kinetics of attrition in the bubbling zone of a fluidized bed and focuses on the development of an equation for attrition in continuous fluidized beds operating at steady state.

Laboratory data describing batch attrition of a limestone sorbent are applied to the integrated equations to describe overall attrition rate in a full-scale continuous system.     

Analytic Model of Laminar‐Turbulent Transition for Bingham Plastics

It is often desirable to operate industrial pipelines transporting non‐Newtonian materials near the transition from laminar to turbulent flow. For the commonly used Bingham plastic model, the Hedström technique overestimates turbulent flow friction losses because it does not take account of viscous‐layer thickening. In the present paper, the Wilson‐Thomas model is applied to predict the transition point for Bingham plastics. Laminar and turbulent friction losses are calculated to show that conditions at transition depend only on the Hedström number. The results are approximated by simplified fit functions. Comparison with existing empirical correlations and experimental data from various sources shows satisfactory agreement.