Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

M1080B无心外圆磨床改进

M1080B无心外圆磨床砂轮及导轮宽度较窄,磨削轴承套圈外圆时,磨削效率低,托板架调整较为繁琐、皮带打滑、磨损较为严重。针对上述问题,提出了相应的解决办法,提高了磨削效率。     

PMU based voltage security assessment of power systems exploiting principal component analysis and decision trees

The need for feature selection and dimension reduction is felt as a fundamental step in security assessment of large power systems in which the number of features representing the state of power grids dramatically increases. These large amounts of attributes are not proper to be used for computational intelligence (CI) techniques as inputs, because it may lead to a time consuming procedure with insufficient results and they are not suitable for on-line purposes and updates.This paper proposes a combined method for an online voltage security assessment in which the dimension of the token data from phasor measurement units (PMUs) is reduced by principal component analysis (PCA). Then, the features with different stability indices are put into several categories and feature selection is done by correlation analysis in each category. These selected features are then given to decision trees (DTs) for classification and security assessment of power systems.The method is applied to 39-bus test system and a part of Iran power grid. It is seen from the results that the DTs with reduced data have simpler splitting rules, better performance in saving time, reasonable DT error and they are more suitable for constant updates.     

Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

Design structure matrix (DSM) method application to issue of modeling and analyzing the fault tree of a wind energy asset

The perpetual energy production of a wind farm could be accomplished (under proper weather conditions) if no failures occurred. But even the best possible design, manufacturing, and maintenance of a system cannot eliminate the failure possibility. In order to understand and minimize the system failures, the most crucial components of the wind turbines, which are prone to failures, should be identified. Moreover, it is essential to determine and classify the criticality of the system failures according to the impact of these failure events on wind turbine safety. The present study is processing the failure data from a wind farm and uses the Fault Tree Analysis as a baseline for applying the Design Structure Matrix technique to reveal the failure and risk interactions between wind turbine subsystems. Based on the analysis performed and by introducing new importance measures, the “readiness to fail” of a subsystem in conjunction with the “failure riskiness” can determine the “failure criticality.” The value of the failure criticality can define the frame within which interventions could be done. The arising interventions could be applied either to the whole system or could be focused in specified pairs of wind turbine subsystems. In conclusion, the method analyzed in the present research can be effectively applied by the wind turbine manufacturers and the wind farm operators as an operation framework, which can lead to a limited (as possible) design‐out maintenance cost, failures' minimization, and safety maximization for the whole wind turbine system.     

采油树平板闸阀柔性密封圈结构优化设计

为了提高采油树平板闸阀密封圈的密封性能,在泛塞封的基础上,设计一种密封圈本体唇边开有锯齿状凸起的新型柔性密封结构;运用有限元分析方法模拟密封圈的工作状况,分析柔性密封结构特性参数对密封圈密封性能的影响,获得不同柔性密封圈结构参数下密封面间接触应力分布规律,并对新型密封结构进行优化。结果表明:密封面间最大接触应力随唇边锯齿数量、唇边夹角度数的增大而增大,随唇谷夹角度数的增大而减小;新型密封结构选择锯齿数量为3、唇边夹角为20°、唇谷夹角为30°的特性参数时,其最大接触应力比常规Y形密封圈提高了15倍;新型柔性密封结构的密封圈与阀杆、阀盖壁面间接触应力比常规Y形密封圈有显著提高,提高了密封圈的密封性能。     

高精度多环片自动装配控制技术

为了实现对微小环片零件的自动化装配,搭建了自动装配系统.通过4根直线导向轴与4个直线轴承来提高系统的导向精度和刚度.采用直线导轨进行各装配作业模块之间的切换,保证了微小环片零件的自动装配与取出.在环片的装配方向上,螺旋升降机和光栅尺实现环片的位置精度控制.在Lab VIEW编程环境中,采用分层软件架构和模块化控制思想,避免了不必要的数据循环检测与丢失,能够达到环片组件的装配精度要求.控制系统分为系统初始化模块、参数设置模块、装配模块和取出模块,自动装配系统通过各个模块间的相互交流配合完成装配任务.采用本文中自动装配系统装配环片的实验结果表明,环片零件装配的最大位置误差为26μm,垂直度误差为17μm,平均装配时间为75 s/片,可满足环片组件所需的精度要求.     

膨胀剂对约束条件下UHPC早期抗裂性能影响的试验研究

超高性能混凝土(UHPC)在钢桥面铺装结构中由于铺装材料受到钢板、栓钉等的约束,加上材料本身水胶比小,更易收缩,早期容易承受拉应力导致开裂。通过在拌和过程中添加膨胀剂可以起到减小收缩的作用,但该方法对于约束条件下的UHPC铺装的早期抗裂性能提升是否有促进作用,仍需通过更多试验进行合理评估和深入研究。通过圆环法对3组不同配方的UHPC在均匀约束条件下的早期抗裂性能进行定量测试,并将试验数据进行回归分析和计算,得到了各组的平均应力发展速率,进而评估了各组的开裂风险等级。试验结果表明,通过在UHPC中加入适量膨胀剂,可使其最终收缩应力减小,并可降低其收缩应力发展速率,进一步降低其在约束条件下的开裂风险。     

AT89C2051芯片在车载产品中的应用

本文论述了采用单片机技术研制成功的泊车用超声波测距仪的基本原理,用AT89C2051作为控制器的实现方案,以及采用软件校正的方法,提高了测量精度和整机的可靠性.