仙游抽水蓄能电站尾水系统充排水试验

为检查工程质量,查找输水系统可能存在的问题并消除隐患,保障电站安全运行,福建仙游抽水蓄能电站在投产发电前,要对输水发电系统进行充水试验与放空排水试验,在试验过程中监测输水系统的应力、应变与渗漏水情况。本文以尾水系统为例,介绍了试验所应具备的工程条件、工作程序及技术要求、试验成果分析和存在问题处理等。试验表明,仙游抽水蓄能电站尾水系统设计合理,施工质量优良,结构可靠,可供同类工程参考与借鉴。     

高温氢工质热物理性质计算分析

氢工质在新能源与动力、航天推进、化工材料等领域有着广泛应用。通过开展高温氢工质热力学与输运性质研究，建立了原子态氢、分子态氢、热解平衡态氢的热物理性质计算模型，开发了热物性计算程序Prop_H_H2，适用范围为温度100~3 500 K、压力104~5×107 Pa 。验证表明，Prop_H_H2在适用范围内计算氢工质的物性参数合理可靠，在温度200~3 000 K、压力104~107 Pa范围内，程序预测值更加准确，相对偏差在±5%左右。本研究可为氢工质相关的航天推进、应用物理学、能源动力等行业的科研和应用提供支持借鉴。     

Characterization of a plasma polymer coating from an organophosphorus silane deposited at atmospheric pressure for fire-retardant purposes

Protective coatings from diethylphosphatoethyltriethoxysilane (DEPETS) have been deposited on different polymer substrates in a plasma discharge operated at atmospheric pressure. Plasma polymer chemistry and structure were characterized by means of Fourier transform infrared spectroscopy (FTIR), laser desorption ionization-mass spectrometry (LDI-MS), nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). A chemical structure of the plasma polymer has been proposed based on the coating molecular characterization. Coatings were deposited on polycarbonate (PC) and polyamide 6 (PA6) substrates. The flame retardant properties of coated substrate samples were assessed using cone calorimetry and compared to those of bare substrates. A significant increase in the time to ignition (TTI), up to +143%, was recorded after coating deposition due to the formation of a high-performance barrier layer at the surface of both polymer substrates.     

Development of green extraction process to produce antioxidant-rich extracts from purple coneflower

The present study was conducted to develop subcritical water extraction (SWE) of Echinacea purpurea flowers. The influence of temperature and extraction time on quality of extracts considering total phenols content, total flavonoids content, antioxidant capacity and extraction yield, was determined. Optimized extraction parameters for maximised investigated responses were as follows: 147.56 °C and 8.43 min. The experimental values agreed with the values predicted, thus indicating the adequacy of central composite experimental design for modelling the SWE of bioactive compounds from E. purpurea. Results of the study also highlighted the potential application of E. purpurea subcritical water extracts as a source of valuable bioactive compounds.     

乙烯、丙烯中微量水含量的分析

采用便携式微量水分析仪和库仑法微量水分析仪测定了乙烯、丙烯试样中的微量水含量,对试样的传输系统、进样量的控制、液体试样的气化和水标准气体的制备方法进行了改进,优化了测试条件。以低吸附惰性管线和小死体积单进单出的不锈钢减压器为试样传输系统,缩短了测试时间。采用液态烃闪蒸气化取样进样器气化液体试样并准确控制试样的进样量,可避免液体试样渐次气化对水含量测定结果的影响及对采样钢瓶大小的限制。采用渗透管发生器制备水标准气体,可验证分析结果的准确度。采用库仑法微量水分析仪测定水含量时,试样流量选择600 m L/min较适宜,开封保存15 d之内的卡尔·费休试剂对测定结果无影响。采用便携式微量水分析仪测定水含量时,选择试样流量在400~800 m L/min之间较适宜。两种仪器的测量结果相近,稳定性好,准确度高,回收率在102%~107%之间,相对偏差小于10%。     

黑龙江省节水增粮行动(2012—2015年)实施方案

文章通过对黑龙江省高效节水现状,存在问题的分析,结合黑龙江省高效节水发展的支撑能力,阐述黑龙江省节水增粮目标、任务及总体布局,为黑龙江省2012—2015年节水增粮实施提供依据。     

Combination of heat treatment and chitosan coating to improve postharvest quality of wolfberry (Lycium barbarum)

The synergistic application of hot water dip at 42 °C for 30 min and 1% chitosan coating on differentiation in postharvest quality traits, microstructure as well as microbiological evolution of wolfberry fruits was investigated. Fresh wolfberry fruits were stored at 2 ± 0.5 °C and 90% relative humidity (RH) for 28 days. Results indicated the combination of prestorage heat treatment and chitosan coating maintained higher levels of ascorbic acid, total phenolic contents and antioxidant capacity as well as lower decay, compared with untreated wolfberry fruits. The possible mechanism was that the heat treatment almost sealed open stomata to limit the sites of pathogen penetration into fruits independently, followed by the biofilm formed by chitosan which controlled secondary infections as well as slowed changes in fruit respiration and metabolic activity in wolfberries. The synergistically treated fruit also exhibited a higher acceptability obtained by sensory analysis after cold storage. In this sense, the integrated application of heat treatment and chitosan coating could be regarded as an effective strategy to extend storage life and maintain the postharvest quality of wolfberry fruits.     

Interlayer Engineering of Molybdenum Trioxide toward High‐Capacity and Stable Sodium Ion Half/Full Batteries

Orthorhombic molybdenum trioxide (MoO₃) is one of the most promising anode materials for sodium‐ion batteries because of its rich chemistry associated with multiple valence states and intriguing layered structure. However, MoO₃ still suffers from the low rate capability and poor cycle induced by pulverization during de/sodiation. An ingenious two‐step synthesis strategy to fine tune the layer structure of MoO₃ targeting stable and fast sodium ionic diffusion channels is reported here. By integrating partially reduction and organic molecule intercalation methodologies, the interlayer spacing of MoO₃ is remarkably enlarged to 10.40 Å and the layer structural integration are reinforced by dimercapto groups of bismuththiol molecules. Comprehensive characterizations and density functional theory calculations prove that the intercalated bismuththiol (DMcT) molecules substantially enhanced electronic conductivity and effectively shield the electrostatic interaction between Na⁺ and the MoO₃ host by conjugated double bond, resulting in improved Na⁺ insertion/extraction kinetics. Benefiting from these features, the newly devised layered MoO₃ electrode achieves excellent long‐term cycling stability and outstanding rate performance. These achievements are of vital significance for the preparation of sodium‐ion battery anode materials with high‐rate capability and long cycling life using intercalation chemistry.     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.