Calculated hardenability for improved consistency of properties in heat treatable engineering steels

Hardenability is one of the most important parameters controlling the heat treated properties of engineering steels. It affects the consistency of response for microstructure, hardness, strength, toughness, and dimensional change (distortion). This study illustrates that a major benefit of controlling hardenability is improving the consistency of dimensional distortion resulting from heat treatment. To facilitate the supply of steels to hardenability limits, especially restricted hardenability, a new technique was developed for the prediction of Jominy hardenability from chemical composition. The technique, termed the “Database Method,” uses measured Jominy hardenability and chemical composition data, contained in a database, to calculate the hardenability for a query composition. Using up to ten known steels, selected from the database with compositions closely matching that of the query steel, a small adjustment is made to the measured hardenability of each known steel allowing for the small difference in composition between the query and chosen steel. The final calculated result for the query steel is taken as the average of the various estimates. The basis of the Database Method is explained, and the advantages are illustrated for selecting engineering grades.     

黄铜中纳米级微裂纹的形核与钝化

黄铜薄膜试样在透射电镜中原位拉伸观察表明，在平衡条件下加载裂发出的位错纯化成无位错区，它是一个应变很高的异常弹性区。当缺口足够锐，外加载荷足够大时，这个非线弹性区中的应力有可能达到原子键合力，从而使纳米级微裂纹在无位错区中不连续形核，或从钝化的原裂纹顶端形核。这个微裂纹一昊形核，即使保持恒位移，也将钝化成空洞或缺口。     

高纯Fe中氢损伤规律的研究

本文采用正电子湮没技术研究了高纯Fe中的氢损伤规律,实验结果表明,在0.5mol/L H_2SO_4溶液中不加毒化剂电解充氢时,产生氢损伤的临界电流密度为20 mA/cm~2;而在0.5mol/L H_2SO_4溶液中加少量As_2O_3作为毒化剂电解充氢时,即使很小的电流密度也会产生氢损伤,配合慢拉伸试验,还发现试样内部产生氢损伤以后,它将控制随后的形变和断裂过程     

提高电火花加工效率的一种方式

基于离子在电磁场下快速而有规律运动的原理。提出了提高电火花加工效率的一种新策略，一个简单的采用功率场效应晶体管的主电路及它们的逻辑驱动信号也同时在文中提出了和分析。     

中频正火焊管的在线矫直

针对焊接油管、套管、锅炉管的焊缝在中频正火热处理时管子弯曲的现象,提出在定径段增设垂直、横向、周向可调的土耳其头机架,对焊管的弯曲实现反弯变形,从而达到在线矫直的目的。     

V形件弯曲凹模最小深度的确定

该文指出了目前广泛使用的经验查表法确定V形件弯曲凹模深度的不合理性，分析了凹模斜壁的作用及其与圆角半径的相互关系，提出了凹模最小的深度的概念和计算公式。     

仪表视窗注射模设计

分析了电器仪表视窗的工艺性,介绍了电器仪表视窗注射模具的结构设计,并对采用公差带来计算成型零件尺寸的方法进行了初步的探讨,可以在一定程度上预测模具的使用寿命。     

搅拌槽内的液-液临界分散

在φ391mm搅拌槽中,分别采用双层Brumagin桨、双层三叶后掠式桨和双层A310桨与7种内构件相组合,在无乳化剂下对油水比(质量比)分别为1∶1.5,1∶2.0的煤油-水体系的液-液临界分散进行了研究。从工业实用的角度出发,对前两种桨找到了一种可替代“轻液挡板”的小挡板及其安装方法:内冷管上均布4块小挡板,B/D=0.08,插入液面深度为0.2D。在φ188mm搅拌槽中,于全挡板条件下,以歧化松香皂为乳化剂,分别采用3种不同几何参数的双层Brumagin桨对油水质量比为1∶1.5的煤油-水体系的临界分散进行了研究。结果表明,与无乳化剂情况相比,液-液临界分散转速(N_c)下降30％～40％,临界分散功耗(P_(cv))下降53％～66％;桨径减小会使N_c和P_(cv)增加。     

五种化合物临界温度和临界压力的测定

The critical properties of five compounds,including propanal,butanal,1-pentanal,2-methel butanal and trimer of ethanal,were determined for the first time by a new capillary quick-flow method. The apparatus was improved with a capillary tube and checked with hexane and 1-heptene as standard reagents. The experimental results proved that the determination of critical properties by quick-flow method with a capillary tube apparatus was successful.     

DEDS-10双子表面活性剂的性能研究

合成了一种新型的DEDS-10双子表面活性剂,用红外光谱对所合成化合物的结构进行了初步表征。DEDS-10的临界胶束浓度cm c为0.47 mmol/L,γcm c为34.5 mN/m,A lC l3、CaC l2和NaC l可以使γcm c降低3.6~1.1 mN/m,其cm c值大约为纯水溶液cm c值的1/5~1/3;加入乙醇,可增加其表面活性,在乙醇的浓度为0.22 mol/L时,其表面张力为30 mN/m左右。与阳离子表面活性剂DTAB和非离子表面活性剂曲拉通X-100复配,可以大幅度地降低cm c和γcm c值,与阴离子表面活性剂TLS复配时,cm c降低,cγm c略有增加。