Numerical Analysis of the Constrained Blister Test

The constrained blister test is investigated through finite element analysis to determine the applicabilities and the limitations of the new technique. Numerical results confirm that the strain energy release rate asymptotically approaches a constant value. These results also show that the test technique and the approximate solution for strain energy release rate are applicable for some practical cases.     

Effects of laser heat treatment on the fracture morphologies of X80 pipeline steel welded joints by stress corrosion

The surfaces of X80 pipeline steel welded joints were processed with a CO2 laser, and the effects of laser heat treatment （LHT） on H2S stress corrosion in the National Association of Corrosion Engineers （NACE） solution were analyzed by a slow strain rate test. The fracture morphologies and chemical components of corrosive products before and after LHT were analyzed by scanning electron microscopy and energy-dispersive spectroscopy, respectively, and the mechanism of LHT on stress corrosion cracking was discussed. Results showed that the fracture for welded joints was brittle in its original state, while it was transformed to a ductile fracture after LHT. The tendencies of hydrogen-induced corrosion were reduced, and the stress corrosion sensitivity index decreased from 35.2% to 25.3%, indicating that the stress corrosion resistance of X80 pipeline steel welded joints has been improved by LHT.     

基于表面反应和扩散迁移控制的灰岩单裂隙渗流—溶解模型及其数值模拟

针对碳酸盐类可溶岩地区水电站坝址流场、化学场以及固相介质属性等随时间发生改变,从而对工程安全运行造成不利影响等问题,研究了灰岩地区地下水运移过程中各物理场间的相互作用,分析了影响灰岩溶解速率的两个因素,即表面反应控制和扩散迁移控制。在此基础上,建立了单裂隙中的渗流—溶解耦合模型,并进行数值求解。模拟结果表明,在垂直裂隙延伸方向,其溶蚀锋面为非齐整平面,而是呈似“虫洞”状非均一变化,而沿裂隙延伸方向即自上游侧向下游方向溶蚀程度逐渐减轻;而通过裂隙的流量呈现随时间逐渐增大的趋势,但变幅不大;根据流量求得的等效水力隙宽,其增幅和增长速率均小于实际平均隙宽;同时,化学场中Ca2+浓度的分布与裂隙开度变化具有相似性,不同时刻下上游侧反应速率R均大于下游侧。就反应机制而言,在初期均受表面反应控制,而随反应进行,位于上游补给区部位转为受扩散迁移控制,但在下游位置仍受表面反应控制。     

Effect of Al in Ti－microalloyed Mn－Ni－Mo welding wire on microstructure and toughness of deposited metal

ＥｆｆｅｃｔｏｆＡｌｉｎＴｉ－ｍｉｃｒｏａｌｌｏｙｅｄＭｎ－Ｎｉ－Ｍｏｗｅｌｄｉｎｇｗｉｒｅｏｎｍｉｃｒｏｓｔｒｕｃｔｕｒｅａｎｄｔｏｕｇｈｎｅｓｓｏｆｄｅｐｏｓｉｔｅｄｍｅｔａｌ￥ＴａｎＣｈａｎｇｙｉｎｇ；ＺｈａｎｇＸｉａｎｈｕｉａｎｄＳｕｎＷｅｉ...     

车轮的热烈和磨损机理与抗热裂耐磨车轮的研制

本文研究了车轮踏面的热裂和磨损机理,结果表明,车轮热裂主要与其含碳量和硬度有关;在使用合成闸瓦时,车轮踏面的磨损率与新形成的“白层”(马氏体)的断裂韧性有关。研制的抗热裂耐磨车轮(55SiMn)取得了明显的运用效果。     

65������Բ������˿����ԭ�����

 65钢热轧圆盘条广泛应用于拉拔高强度钢丝。在拉拔钢丝的过程中断裂现象时有发生。用金相手段分析断裂原因。分析结果认为：导致拉丝断裂的原因是拉丝工艺不当。     

Stress－rupture Property and Microstructure of Yttria Dispersion Strengthened Alloy MA956

Ｓｔｒｅｓｓ－ｒｕｐｔｕｒｅＰｒｏｐｅｒｔｙａｎｄＭｉｃｒｏｓｔｒｕｃｔｕｒｅｏｆＹｔｔｒｉａＤｉｓｐｅｒｓｉｏｎＳｔｒｅｎｇｔｈｅｎｅｄＡｌｌｏｙＭＡ９５６ＳｈａＷｅｉ（沙维）（ＤｅｐａｒｔｍｅｎｔｏｆＣｉｖｉｌＦｎｇｉｎｅｅｒｉｎｇ，ＴｈｅＱｗｅ...     

TENSILE FRACURE IN AN Al-Li ALLOY 8090

ＴＥＮＳＩＬＥＦＲＡＣＵＲＥＩＮＡＮＡｌ－ＬｉＡＬＬＯＹ８０９０￥Ｊｉａｎｇ，Ｄａｍｉｎｇ；Ｗａｎｇ，Ｙｉｎｏｎｇ；Ｈｏｎｇ，Ｂａｎｄｅ；Ｌｅｉ，Ｔｉｎｇｑｕａｎ（ＨａｒｂｉｎＩｎｓｔｉｔｕｔｅｏｆＴｅｃｈｎｏｌｏｇｙ，Ｈａｒｂｉｎ１５００８０）Ｓｕ...     

工程机械用800MPa低合金高强度钢焊接接头断裂韧性评价

对调质状态800MPa低合金高强度钢及其焊接接头进行了系列温度的断裂韧性测试,讨论不同焊接方法对焊接接头断裂韧性的影响。发现板材的轧制方向对断裂韧性影响显著,LT方向试件的断裂韧性远超过TL方向试件的断裂韧性。在-60℃以上,母材处于上平台延性断裂范畴。在-80℃,裂纹扩展过程中有延脆断裂模式的转变。焊条电弧焊焊缝的断裂韧性与气体保护焊焊缝的断裂韧性相当。尽管常温下焊缝金属的断裂韧性甚至优于母材,但随着试验温度的降低,焊缝金属的断裂韧性迅速下降。在-20℃已发生断裂模式转变,这在结构服役时要引起重视。本研究为大型工程机械的断裂安全评定奠定了基础。