高压锅炉补给水系统管道的腐蚀

讨论了锅炉补给水管道的腐蚀情况 ,指出溶解氧和二氧化碳是产生腐蚀的主要原因 ,其腐蚀速率为0 .4 2mm/a。确保真空除气系统正常运行和二级除盐水箱的密封效果是控制腐蚀的主要手段。在此情况下 ,该管线尚可运行 7年     

罗茨真空泵的溢流阀与旁通阀的组合

在简要地介绍了罗茨泵功能的基础上，通过溢流阀的改进设计，使溢流阀成为既能旁通又能溢流的组合阀，罗茨泵的功能将更加完备。     

耐高温绝缘GFRP管的真空辅助树脂传递成型工艺研究

阐述了耐高温绝缘GFRP管的成型工艺及原材料选择，并对影响成型工艺的主要因素作了理论分析及试验验证。研究表明，以TDE－85／DDS体系为为基体，以无碱无捻玻璃纤维方格布为增强材料，用VARTM工艺成型的石油勘探高性能平衡管完全满足技术要求。     

真空热处理工艺参数的选取

通过多种材料、多种工件、多批次的加工，对常见真空热处理工艺参数的确定，摸索出一些经验公式，并在实际生产中取得很好效果。     

沪芦高速公路软土地基设计与研究

软土地基的处理是影响高等级公路工程质量和使用性能的重要因素 ,针对沪芦高速公路的工程特点 ,通过对不同土层力学性能分析 ,地基稳定验算以及沉降计算提出地基处理方案 ,并介绍通过地基处理后获得的显著效果     

粉末布法制备SiC/Ti基复合材料

用粉末布法制备了低成本SiC/Ti基复合材料.结果表明,采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布;热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段,合理除气后,基本没有残余物.使用真空热压工艺制备的SiC/Ti基复合材料,纤维分布基本均匀,纤维与基体的界面结合良好.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

真空行业现状及未来国内市场

简单扼要的概述了真空行业的发展历史，以较详细的统计数据阐述了2002年行业经济运行情况，并通过对相关行业“十五”发展规划的研究，对今后5～10年真空设备的市场进行了分析预测。     

成形工艺对快速凝固Al—Cu—Mg合金组织和性能的影响

采用自制离心雾化装置制取了快速凝固LY12硬铝合金粉末,研究了以该粉末制成的真空热压件和挤压丝材的组织和性能。结果表明,所得粉末为泪滴状,其显微组织为树枝状晶和胞状晶。真空热压件密度高时所对应的强度高。450℃、10min、150MPa为较合理的工艺,此时粉末颗粒间结合密实,晶粒尺寸没有明显改变。在500℃热挤压时,挤压丝的组织已发生了再结晶,晶粒尺寸仍较细小。挤压丝材的抗拉强度达460MPa,其断口为韧窝状,韧窝尺寸小于3μm,且分布均匀。     

Characterization and catalytic gasification of the aqueous by-product from vacuum pyrolysis of biomass

Spruce wood residues were treated in a vacuum pyrolysis Process Development Unit with a throughput capacity of 28 kg/h. Two aqueous phase condensate samples with COD concentration varying between 190 and 255 g/L were produced and sequentially extracted with dichloromethane and ethylacetate solvents. The soluble organic matter was composed of acidic, phenolic, alcoholic and ketonic compounds. The insoluble fraction was sequentially distilled at 100 and 110°C under atmospheric pressure. Mainly water was recovered in the first distillate, while the second distillate contained 30.4% formic and acetic acids, 69.4% water and 0.2% residual organic compounds. The distillation residue was rich in oxygen and was essentially insoluble in any organic solvent. The two aqueous phase pyroligneous samples were treated in Bat-telle's Thermochemical Environmental Energy System (TEESr?), a registered service mark of Onsite*Ofsite, Inc. of Duarte, California, U.S.A. The results of the tests showed that similar results were obtained with either feedstock. In batch tests a COD reduction of 99% was achieved. The product gas composition was typically about 49% methane, 5% hydrogen, 1 % ethane and 45% carbon dioxide. Tests in a continuous stirred-tank reactor produced reproducible data which can be used for process scale-up. Catalyst lifetime was identified as needing further improvement. The preliminary results demonstrated the technical feasibility of the catalytic gasification process as a useful step in the recovery of energy from the secondary condensate stream and the cleanup of the by-product water from vacuum pyrolysis of wood.