一种新的基于快速功控的多普勒估计

针对采用快速功控的移动通信系统提出了一种简便的多普勒估计方法。该方法利用功控后的接收信号电平的平稳性与最大多普勒频移有密切关系这一特点，通过测量接收信号电平的平稳性估计多普勒频移。文中在单径瑞利衰落信道条件下对这一方法进行了仿真验证，并同文献中提出的COV方法进行了比较，仿真结果表明在信道变化不是太快时本方案有较好的估计精度。     

厚膜永磁阵列微致动器的磁路研究

研究了厚膜永磁阵列微致动器中的磁场分布，并研究了永磁阵列单元几何尺寸对微致动器电磁力的影响。结果表明，厚膜永磁阵列单元高宽比和磁体单元间隔对微致动器电磁力影响较大磁徕单元高宽比为0．7是一个比较合适的尺寸。     

岩石物理横波速度曲线计算技术

横波速度是地震勘探中的重要参数。针对实际生产中缺乏横波速度测井曲线资料，利用经验公式计算精确度不高的问题，通过对横波速度计算理论模型的研究分析，选择Blot-Gassman模型法，利用岩石矿物成分、流体成分、孔隙度及密度等测井曲线进行横波速度测井曲线的计算，并对横波速度计算技术和流程进行研究。在实际工区进行了横波速度曲线计算，计算结果与实测横波吻合程度较高，误差小于10％，该技术在储层和流体识别预测的应用中取得了较好效果。     

介质流速对在线焊接管道极限压力的影响

运用有限元法对不同介质流速下在线焊接时的温度场进行了数值模拟,内部介质流动对焊接温度场的影响通过确定介质与管壁的换热系数来考虑;根据温度计算结果,获得管道的剩余强度因子,进而判定管壁是否烧穿。研究表明,随着流速的增大,焊缝位置处外壁上的峰值温度无明显变化,而内壁上的峰值温度随之下降;在线焊接管道的剩余强度因子及所能承受的极限压力呈上升趋势,且在一定范围内增大明显,故应充分利用该流速变化范围的特点以确定最佳施工条件。     

现代电子工业Cpk评价中的特殊问题

现代电子工业生产具有许多新的特点，如果不针对具体情况，均采用传统工业生产中广泛使用的常规方法计算其工序能力指数，评价生产工艺水平，将可能导致错误的结论。总结了电子工业生产中工艺参数的典型特点，并讨论了工序能力指数的正确计算方法。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

Modeling of Material Deformation Kinetics in the Prefracture Zone

Based on the concept of complete stress–strain diagrams, we propose a new model describing the law of stress distribution in the prefracture zone in plastic materials in view of the type of the stressed state.     

Analysis of spontaneous electrochemical oscillations by energy distribution technique

Analysis of non-stationary electrochemical oscillations emerges utilization of the techniques allowing an observation of time evolution of their parameters such as instantaneous frequency, amplitude or frequency band. An algorithm of extraction of these parameters can be based on one of linear or quadratic time-frequency representations of oscillations record. In this paper, the authors present representatives of such transformations (Choi-Williams and Cone-shaped) originating from one of the most popular joint time-frequency energy distribution—Wigner-Ville distribution. Short introduction to the mathematics of the topic discussed is provided, then the authors present an example of application in the analysis of current oscillations of copper dissolution process.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Sociotechnical systems, risk management, and public health: comparing the North Battleford and Walkerton outbreaks

Accidents in different complex sociotechnical systems are rarely compared using the same theoretical framework for risk management. We conducted a comparative analysis of two Canadian public health disasters involving drinking water distribution systems, the North Battleford Cryptosporidium parvum outbreak in April 2001 and the Walkerton E. coli outbreak in May 2000. Both accidents resulted from a complex interaction between all levels of a complex sociotechnical system. However, the low-level physical and individual factors differed in the two cases, whereas, the high-level governmental and regulatory factors tended to be the same. These findings may have implications for the design of public policies to minimize risk in complex sociotechnical systems.