HVOF喷涂NiCr-Cr3C2过程中Laval管壁结瘤成因的探讨

围绕超音速火焰喷涂NiCr-Cr3C2涂层时在Laval管内壁产生结瘤的问题，在分析结瘤产物显微结构的基础上探讨了形成结瘤的原因。研究发现，结瘤产物具有层状组织结构，说明结瘤的形成机制与涂层形成机制相似；在HVOF喷涂时，导致Laval管内壁结瘤的原因主要包括：喷涂材料、喷涂粉末颗粒粒度、喷涂工艺参数、Laval管的内表面粗糙度。     

Effects of temperature and blank holding force on biaxial forming behavior of aluminum sheet alloys

Biaxial forming behavior is investigated for three aluminum sheet alloys (Al 5182 containing 1% Mn (5182+Mn), Al 5754, and 6111-T4) using a heated die and punch in the warm forming temperature range of 200–350 °C. It is found that, while all three alloys exhibit significant improvement in their formability compared with that at room temperature, the non-heat-treatable alloys 5182 + Mn and 5754 give higher part depths than that of heat-treatable 6111-T4. The formability generally increases with decreasing BHP (BHP), but increasing the forming temperature and/or BHP minimizes the wrinkling tendency and improves the forming performance. The stretchability of the sheet alloys increase with increasing temperature and increasing BHP. For the alloys and forming conditions involved in the current study, the formability, measured in terms of part depth, comes mainly from the drawing of metal into the die cavity, although stretching effects do influence the overall forming behavior. The optimum formability is achieved by setting the die temperature 50 °C higher than the punch temperature to enhance the drawing component. Setting the die temperature higher than the punch temperature also improves the strain distribution in a part in such a manner that postpones necking and fracture by altering the location of greatest thinning.     

Al-18%Si合金在梯度强磁场中凝固时初生硅的行为

研究了Al-18%Si合金在10 T梯度强磁场下加热至半固态和全熔态后的凝固过程,观察了初生硅的分布和形态,测定了其冷却曲线.结果表明:在磁场的磁感应强度和磁场梯度的乘积Bz·dBz/dz为正时,初生硅向上部聚集;而在Bz·dBz/dz为负时,初生硅向下部聚集;在强磁场下,加热至全熔态冷却下来的凝固组织中初晶硅的形态发生了明显的改变,由板片状转变为块状,初晶硅显著细化.对强磁场细化初晶硅的机制进行了探讨.     

Investigation on gradient material fabrication with electron beam melting based on scanning track control

A new electron beam control system was developed in a general vacuum electron beam machine by assembling with industrial control computer, programmable logic control （PLC）, deflection coil, data acquisition card, power amplifier, etc. In this control system, scanning track and energy distribution of electron beam could be edited off-line, real-time adjusted and controlled on-line. Ti-Mo gradient material （GM） with high temperature resistant was fabricated using the technology of electron beam melting. The melting processes include three steps, such as preheating, melting, and homogenizing. The results show that the GM prepared by melting technology has fine appearance, and it has good integrated interface with the Ti alloy. Mo and Ti elements are gradually distributed in the inter.face of the gradient material. The microstructure close to the Ti alloy base metal is α ＋ β basket-waver grain, and the microstructure close to the GM is a single phase of β solid solution.     

CdZnTe Crystal Growth by Vertical Gradient Freezing Method

ＣｄＺｎＴｅＣｒｙｓｔａｌＧｒｏｗｔｈｂｙＶｅｒｔｉｃａｌＧｒａｄｉｅｎｔＦｒｅｅｚｉｎｇＭｅｔｈｏｄＨｏｕＱｉｎｇｒｕｎ；ＷａｎｇＪｉｎｙｉ；ＤｅｎｇＪｉｎｃｈｅｎｇ；ＤｕＢｉｎｇ，（侯清润）（王金义）（邓金诚）（杜冰）；ＬｉＭｅｉｒｏｎｇａｎｄＣ...     

环形截面提升管内颗粒的运动行为

采用PDPA(phase Doppler particle analyzer system)及磷光颗粒示踪技术对环形截面提升管中颗粒的运动行为进行了研究。与传统提升管相比，环形截面提升管中颗粒速度分布的均匀性有所改善，其最高速度与最低速度之差变小。环形截面提升管最大速度值出现在相对径向位置φ=0.3-0．4处。与传统提升管相似，环形截面提升管内颗粒的轴向返混较严重，停留时间分布曲线存在较明显的拖尾，其中颗粒的轴向Peclet数与传统提升管也处于同一数量级范围。提升管床结构的改变并未显著改变其中气固流动的微观相结构，稀相与密相颗粒团微观两相仍然存在，这种微观相结构是造成颗粒严重返混的决定性原因：稀相中的颗粒与密相颗粒团中的颗粒分别造成了颗粒停留时间分布曲线的前峰与拖尾峰。     

双通道喷嘴渣油气化过程(Ⅰ)冷模实验

基于对3套8.53MPa双通道喷嘴渣油气化装置普遍存在的工程现象的思考,组织了模型气化炉冷态试验。测试了3种模型在6种射流速度下的停留时间分布,7种模型在2种射流速度下的速度分布。给出了停留时间分布密度函数、无因次半速度半径轴向增长、径向射流最大速度轴向衰减和径向速度分布计算公式。     

用直接纺丝法制芳纶短纤维

研究了直接纺丝制取芳纶短纤维的新方法。讨论了纤维长度、直径及力学性能与纺丝条件的关系。发现影响纤维长度的主要因素是空气层高度和喷丝速度,影响纤维直径的主要因素为喷口直径及喷丝速度。此外,还用PPTA短纤维制成了均匀的PPTA"浆粕"纤维。     

硅铁复合型絮凝剂的实验研究

研究了硅铁复合型絮凝剂的制备方法和絮凝性能 ,确定了其最佳反应条件 ,所得复合型絮凝剂对江水的除浊性能优于聚合硫酸铁 (PFS)和聚合氯化铝 (PAC)。     

水库水温分层对浮式取水口前流速分布的影响

由于目前缺乏对浮式取水口前流场变化规律的研究,以分析水库水温分层对取水口前各断面流速分布影响为目标,依据某水库水温资料,采用k-ε紊流模型对浮式取水口前流场进行三维数值模拟,针对水库水温均一和水温分层的两种情况,研究取水口前流速分布,分析水库水温分层对取水口前各断面流速分布的影响。研究结果表明,在浮式取水口附近,水温均一和水温分层的流速分布存在着差异,这种差距随着取水流量和淹没深度的增大而减小。研究成果可为浮式管型取水设施的应用和运行提供技术支持,为取水水温预测提供理论依据。