翻领成型器领口曲线的程序计算展开法

根据翻领成型器领口曲线的数学模型，介绍一种利用计算器复杂公式存贮的特殊功能，预编程序计算相关参数。然后画领口曲线展开图的方法。     

外焊缝自动跟踪系统

介绍了外焊缝自动跟踪系统的组成及工作原理，简述了传动部分ＧＴＲ－ＰＷＭ调速系统，给出了系统的硬件电路。该跟踪器具有结构简单，体积小，性能稳定等特点，在生产线上获得了成功的应用。     

隔河岩重力拱坝拱座深层处理平面有限元分析

清江隔河岩重力拱坝坝基地质条件复杂，软弱夹层，断裂构造多，岩溶发育，两岸拱座存在局部滑动问题。     

硅灰混凝土的研究及其在公路道面的应用

 了提高道路路面混凝土的抗磨能力，采用硅灰代替部分水泥的方法，对硅灰混凝土的性能进行了较系统的试验研究。成果表明其抗压强度、抗弯强度、抗磨强度等指标都得到明显提高，全面达到和超过了规范要求。并已在丹江口水利枢纽上坝公路中得到应用，实践证明硅灰混凝土技术可靠、经济合理、易于施工。特别是抗磨度的提高，对延长公路路面的使用寿命具有重要意义。     

炸药压装爆炸事故剖析

文中依据压爆事故的实例，对其产生的原因做了剖析，在剖析的基础上对压爆机理做了简要的阐述并提出了相应的预防措施。     

Convergence of iterated boolean sums of simultaneous approximants

Explicit error estimates are given for the iterated Boolean sum of a sequence of simultaneous approximants; the rate of convergence is shown to be improved for smooth functions. The general results are applied in the case of the Bernstein, Durrmeyer and Stancu operators.     

在役加氢反应器试验板脆化和氢损伤的测定与研究

充分利用了带主焊缝的役后试板，在国内首次开展回火脆化、氢介质下断裂韧性与疲劳扩展的研究，结果表明，加氢反应器焊缝有明显的脆化表现。同时，核查了反应器开停车升温速度和降温速度规定，以及确定了裂纹允许尺寸的参考数据，为今后安全运行提供了充分的依据。     

一般应力比时焊接结构S－N曲线的预测方法

本文考虑了焊接结构的几何形状、受载形式、应力比、残余应力、尺寸效应以及材料等因素对疲劳寿命的影响，利用Ｐｅｔｅｒｓｏｎ公式和极值疲劳切口系数概念，建立了一般应力比时焊接结构Ｓ－Ｎ曲线的预估模型．文中对几类典型的焊接结构的Ｓ－Ｎ曲线进行了预测，预测值与实验结果符合较好．本文方法可以大量减少疲劳实验，具有一定的工程实用价值．     

DETERMINATION OF TOTAL NITROGEN IN BARLEY AND MALT BY COMBUSTION METHOD—COLLABORATIVE TRIAL

A combustion method, relying on the Dumas principle, for the determination of total nitrogen in barley and malt, has been collaboratively tested by the Analysis Committee of the European Brewery Convention. Repeatability, r₉₅, and reproducibility, R₉₅, values were 0.063 and 0.116% of dry matter, respectively, for samples with nitrogen contents in the range 1.23 to 1.86% N of dry matter. There was no significant difference between these values for barley and malt. The Analysis Committee approved the adoption of the combustion method for inclusion in Analytica EBC as an alternative method.     

A method of estimating the standard gibbs free energy of formation

Standard Gibbs free energy of formation (ΔG_f⁰), an important property needed in design calculations has been estimated using molar refraction, R_M. The linear relationships derived between ΔG_f⁰ and R_M tested with the data on 8 series of hydrocarbons at 228 compounds yielded average deviations comparable to the methods cited in recent literature. The method can be used as an alternative to the existing ones, because of its simplicity combined with reasonable accuracy.