Numerical simulation model of vibration responses of rectangular plates embedded with piezoelectric actuators

A numerical simulation model for random large amplitude vibration control of composite plate using piezoelectric material is presented. The H_∞ control design is employed to suppress the large amplitude vibrations of composites plates under random loading. The numerical simulation model is developed and based on the finite element method. The finite element governing equation includes fully coupled structural and electrical nodal degrees of freedom, and consider the von Karman large amplitude vibration. The modal reduction method using the structural modes is adopted to reduce the finite element equations into a set of modal equations with fewer degrees of freedom. The modal equations are then employed for controller design and time domain simulation. In the simulations without control, the value of the linear mode to the nonlinear deflection is quantified; and the minimum number of linear modes needed for accurate model is obtained. In the simulations with control, it is shown that the truncated modes, which are neglected in the control design, deteriorate the controller performance. Generally, the vibration reduction level is not monotonically increasing with the size of the piezoelectric actuator. The optimal piezoelectric actuator size depends on the excitation level. For higher excitation level, optimal actuator size is larger. The H_∞ controller based on the linear finite element formulation gives better vibration reduction for small amplitude vibration, but it still gives reasonable performance for large amplitude vibration provided that the piezoelectric actuator is big and powerful enough.     

机组油膜振荡故障的诊断和处理

通过对广州发电厂1号机组3号轴承突发剧烈振动的现象和测试结果的分析，对振动故障进行诊断并提出解决办法，对3号轴承轴瓦进行处理后，机组恢复正常运行状态。     

中速球磨机运行中振动原因分析及消除措施

中速球磨机由于其独特的优点受到电厂的欢迎，但在运行过程中时有振动现象发生，影响了磨煤机及锅炉机组安全运行。本文根据磨煤体振动大与磨煤机电流的变化规律，针对ZQM-216型中速球磨机运行中的振动原因进行分析，并提出消除措施，以供同类型机组参考。     

转子系统热膨胀状态下固有横振频率

把转子的惯性力看成作用在轴上的外力,采用新的非线性渐近法研究热膨胀对转子系统固有横振频率的影响.     

结构振动控制中压电阻尼技术研究—压电被动阻尼技术（一）

压电阻尼技术有两种类型：压电被动阻尼技术和压电主动阻尼技术。本文对其中的压电被动阻尼技术进行了研究，结果表明：通过给压电元件并联适当的外部电路，可使压电系统具有与粘弹阻尼材料及动力吸振器相似的物理特性。合理配置电路参数，可以实现最优阻尼比。     

新型并条胶辊套筒的特点及运用

为了解决常规并条胶辊套筒存在的易发热、易漏油，芯轴易弯曲磨损以及保养、能耗等问题，介绍了新型免加油并条胶辊套筒的性能特点并以实际生产数据进行对比；说明实际使用该新型并条胶辊套筒综合效果好，具有省工省时、降低消耗、质量稳定、使用寿命长、总投资少等优点。     

爆破地震效应及其控制措施分析

通过对爆破地震效应的产生、危害及其影响因素分析，给出了减小爆破地震效应的措施。     

EDA介质快慢横波时差和振幅-方位曲线的实验分析

在含垂直定向裂隙的各向异性（EDA）介质中，地震快、慢横波传播的时差及振幅随裂隙（缝）方位变化曲线能反映裂缝的密度、走向和介质的性质，这对多波地震资料的处理、解释有着重要意义。但受观测条件限制以及噪声的影响，在横波分裂记录上，同相轴往往会出现扭曲、倾斜和不规则抖动等现象，给快、慢横波时差的求取和振幅-方位曲线的绘制带来误差。设计了EDA介质物理模型，并利用岩石超声波测量系统获得了快、慢横波记录；分析记录可知，在相同传播方向的分裂横波具有走时和传播速度不随裂缝方位变化的恒定性特征；以此为基础，提出了利用平均法和瞬时振幅法来计算快、慢横波的走时时差和绘制振幅-方位曲线，以提高精度。利用物理模型实验得到的2个正交横波（S1波与S2波）的快、慢横波记录，分别用平均法和瞬时振幅法计算了快、慢横波走时的平均值、时差和均方差，并绘制了相应的振幅一方位曲线。结果表明，采用上述2种方法，消除了同相轴扭曲、倾斜和不规则抖动等对计算结果的影响，时差的计算是可靠的，振幅一方位曲线的绘制是合理的。     

Random Vibration of Systems with Viscoelastic Memory

The equation of motion of linear dynamic systems with viscoelastic memory is usually expressed in a integrodifferential form, and its numerical solution is computationally heavy. In two recent papers, the writers suggested that the system memory be accounted for through the introduction of a number of additional internal variables. Following this approach, the motion of the system is governed by a set of first-order, linear differential equations, whose solution is quite easy. In this paper, the approach is extended to single-degree-of-freedom systems subjected to random, nonstationary excitation. The equations governing the time variation of the second-order statistics are derived, and an effective step-by-step solution procedure is proposed. Numerical example shows the accuracy of the procedure for white and nonwhite excitations.     

基于DDS改进BT-4型扫频仪

基于DDS技术,改造BT 4型扫频仪中的扫频信号发生器,使其具有高稳定度、高分辨率、高精度的特点。同时为了使扫频仪能够对被测电路的动态范围进行检测,使扫频仪得到更广泛的应用,运用了AGC控制技术,首先使电压稳定在10 V;然后通过控制D/A使输出电压按测试需要输出。硬件给出了具体电路参数,软件给出了相应软件流程,总结了其他波型产生的方法。