Self-excited vibration problems of maglev vehicle-bridge interaction system

The self-excited vibration problems of maglev vehicle-bridge interaction system were addressed, which greatly degrades the stability of the levitation control, decreases the ride comfort, and restricts the cost of the whole system. Firstly, the coupled model containing the quintessential parts was built, and the mechanism of self-excited vibration was explained in terms of energy transmission from levitation system to bridge. Then, the influences of the parameters of the widely used integral-type proportion and derivation（PD） controller and the delay of signals on the stability of the interaction system were analyzed. The result shows that the integral-type PD control is a nonoptimal approach to solve the self-excited vibration completely. Furthermore, the differential-type PD controller can guarantee the passivity of levitation system at full band. However, the differentiation of levitation gap should be filtered by a low-pass filter due to noise of gap differentiation. The analysis indicates that a well tuned low-pass filter can still keep the coupled system stable.     

数控车床振动的控制Ⅰ:振源与力学模型

本文论述了数控车床的振源，建立了三种力学模型，并进行了分析，为数控机床的数学模型的建立和振动的控制打下了基础。     

冷轧工作辊摩擦不稳定分析及其抑制对策

对冷轧机工作辊由于摩擦力引起的垂直、横向振动作了定性分析，指出了它们的危害，提出了预防措施。     

ZL114铝合金激光--龟弧的复合焊接

设计了一种激光-电弧复合热源焊接ZL114合金的新工艺，并对焊后的试件进行了X光检测、抗拉强度和全相组织等实验。结果表明，该种新工艺对铝合全有良好的适应性和可行性，是焊接领域的一个趋势。     

TEM IMAGING TECHNIQUE

This imaging technique is used for approximate interpretation of TEM data including ungrounded loopsource and grounded line source soundings.Loop source data can be collected as central-loop soundings or asout-of-loop soundings with a short or long offset configuration.The imaging method is based on the same princi-ple as that employed by Fullager(1989),with apparent resistivities computed directly from time-derivative data,db/d,and then associated with depths according to image theory.     

逆变电源的可靠性及其提高途径

影响逆变焊接电源可靠性的因素是多方面的.如产品的设计和生产等各个环节.根据实践经验提出了解决可靠性问题的一些有效途径和方法.     

用PID控制弧焊逆变电源的试验研究

本文介绍了对逆变电源进行数字PID控制的原理和方法,分析了采样周期、PID参数及不同的焊接工况对控制特性的影响。试验表明,只要恰当地选择PID(或PI)参数,不仅能实现高精度的恒流控制,而且能使系统的动态性能显著提高。     

Modal analysis of human body vibration model for Indian subjects under sitting posture

Need and importance of modelling in human body vibration research studies are well established. The study of biodynamic responses of human beings can be classified into experimental and analytical methods. In the past few decades, plenty of mathematical models have been developed based on the diverse field measurements to describe the biodynamic responses of human beings. In this paper, a complete study on lumped parameter model derived from 50th percentile anthropometric data for a seated 54- kg Indian male subject without backrest support under free un-damped conditions has been carried out considering human body segments to be of ellipsoidal shape. Conventional lumped parameter modelling considers the human body as several rigid masses interconnected by springs and dampers. In this study, concept of mass of interconnecting springs has been incorporated and eigenvalues thus obtained are found to be closer to the values reported in the literature. Results obtained clearly establish decoupling of vertical and fore-and-aft oscillations.     

Whole-body vibration exposure in sport: four relevant cases

This study investigates the whole-body vibration exposure in kite surfing, alpine skiing, snowboarding and cycling. The vibration exposure was experimentally evaluated following the ISO 2631 guidelines. Results evidenced that the most critical axis is the vertical one. The weighted vibration levels are always larger than 2.5 m/s² and the vibration dose values are larger than 25 m/s^1.75. The exposure limit values of the EU directive are reached after 8–37 min depending on the sport. The vibration magnitude is influenced by the athletes’ speed, by their skill level and sometimes by the equipment. The large vibration values suggest that the practice of sport activities may be a confounding factor in the aetiology of vibration-related diseases.     

Predicting and controlling risks from human exposures to vibration and mechanical shock: flag waving and flag weaving

At work or in leisure activities, many people are exposed to vibration or mechanical shocks associated with risks of injury or disease. This paper identifies information that can be used to decide whether there may be a risk from exposure to hand-transmitted vibration or whole-body vibration and shock, and suggests actions that can control the risks. The complex and time-varying nature of human exposures to vibration and shock, the complexity of the different disorders and uncertainty as to the mechanisms of injury and the factors influencing injury have prevented the definition of dose–response relationships well proven by scientific study. It is necessary to wave a flag indicating when there is a need to control risks from exposure to vibration and shock while scientific enquiry provides understanding needed to weave a better flag. It is concluded that quantifying exposure severity is often neither necessary nor sufficient to either identify risks or implement measures that control the risks.Practitioner Summary: The identification of risks associated with exposure to vibration and mechanical shock cannot, and need not, rely solely on the quantification of exposure severity. Qualitative methods can provide a sufficient indication of the need for control measures, which should not be restricted to reducing standardised measures of exposure severity.