有限体积法求解立体角离散误差

为解决采用有限体积法求解辐射传输方程时引起离散误差的问题,从有限体积法立体角内热流密度的求解过程出发,运用泰勒级数推导了近似误差的表达式,并分析影响离散误差的各种因素,包括离散射线数,辐射强度分布,假散射及网格比.根据分析结果,采用辐射强度的连续分布模型,模拟了各种因素对误差的影响.结果表明,辐射强度的分布函数对于有限体积法的离散误差有一定程度影响.当增加网格数及减小网格尺寸比时,可以有效地减小离散误差.假散射与离散误差间呈较强的非线性耦合关系.     

K8型单层球面网壳支座减震

为了对跨度为60 m的K8型单层球面网壳进行了减震分析,分别将结构的支座设置成弹性支座和弹性阻尼支座,对结构进行减震控制.结合对结构在有控和无控状态下自振特性的分析,阐述了单层球面网壳结构的减震控制原理.在常遇地震作用下,得到网壳结构的最大水平位移、减震支座的最大水平位移、最大支座反力和最大杆件内力.通过改变支座的刚度和阻尼系数,对两种减震方案的减震效果进行比较.研究结果表明:两种减震装置均有效地控制了K8型单层球面网壳结构的支座反力,弹性阻尼支座还可以明显地降低减震支座的水平位移.     

大口径光学透镜瞬态温度场模拟

为考察热辐射效应对光学元件稳、瞬态温度场的影响,给出了考虑辐射和导热耦合换热情况下复杂几何结构光学透镜稳、瞬态热特性的适体坐标下离散坐标法.对喷管形和圆柱形介质进行计算并与其他方法比较表明,建立的适体坐标系下辐射与导热耦合换热计算方法精度较好.对两端为球缺中间为圆柱的大口径透镜内的辐射与导热耦合换热过程进行了数值模拟.计算结果表明,为了精确地预测半透明介质如透镜内的温度分布,应该考虑辐射与导热耦合作用,且应当考虑介质的光谱特性.     

城市污水的层流换热特性理论

为有效利用城市污水热能,以污水源热泵系统中的流动工质——城市污水为研究对象,通过理论分析的方法,对其层流状态下的换热特性进行理论推导和实验验证.结果表明:污水作为热泵的冷热源,有良好的换热特性,推导得出的换热准则关联式h=4.53λ/D,为污水源热泵系统设计提供依据,同时为应用污水余热技术提供理论基础.     

强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

Investigation on film cooling characteristics from a row of converging slot-holes on flat plate

Experimental and numerical researches were conducted to investigate the cooling performance of a single row of consoles (converging slot-hole) on a large-scale flat-plate model. The results show that the coolant flow from a row of consoles shows good lateral uniformity of adiabatic effectiveness, with regions of slightly enhanced cooling occurring between the consoles. For the console cooling geometry, the interaction between coolant jet from inclined console and the mainstream flow results in reasonable vo...     

基于循环维纳滤波的振动信号去噪算法研究

振动信号的去噪需要在滤除噪声的同时尽可能避免相位失真。传统的锐截止低通滤波器或FIR滤波器无法在去噪效果和线性相位之间取得平衡,难以满足振动信号的去噪需求。针对这一问题,将线性相位的维纳滤波算法引入到振动信号的去噪中,并结合振动信号的循环平稳特性,形成了振动信号的循环维纳滤波算法。文中以直接维纳滤波为基础对循环维纳滤波算法的原理进行了深入分析和仿真实现,并基于实测汽轮机振动信号对算法的去噪性能进行了讨论。理论分析及算法仿真表明,循环维纳滤波算法在保证线性相位的前提下有较好的去噪效果,能够解决传统去噪算法所存在的去噪效果与线性相位难以均衡的问题。     

Mixed convection heat and Mass transfer in a vertical channel with film evaporation

Numerical results are presented for effects of latent heat transport associated with film vaporization on laminar mixed convection heat and mass transfer in a vertical channel with a half channel width b = 0.01 m. The influences of the inlet liquid mass flowrate and wall temperature on the film vaporization and the associated heat and mass transfer characteristics are examined for air-water and air-ethanol systems with gas Reynolds number Re_g = 2000. Predicted results obtained by including transport in the liquid film are contrasted with those where liquid film transport is neglected, showing that the assumption of an extremely thin film made in Lin et al. (1988) and Yan and Lin (1989) is only valid for systems having small liquid mass flow rates. Additionally, it is found that the interfacial heat flux is predominantly determined by latent heat transfer connected with film evaporation.     

CJ91胶粘剂在螺旋振动光整机中的应用

螺旋振动光整机槽内壁的橡皮保护层由于老化及磨损等原因出现裂口甚至脱落现象，严重影响设备的使用寿命和闸把壳体的外观质量。通过分析和试验筛选出螺旋振动光整机的理想胶粘荆——CJ91胶粘剂并介绍了粘接修补工艺。     

Novel fluorescent polynorbornenes with multi-functional armed structure by using highly stable block macroinitiators via a combination of living ring-opening metathesis polymerization and atom transfer radical polymerization

Novel organosoluble fluorescent polynorbornenes with multi-functional armed structure were designed and prepared by using highly stable block macroinitiators via a combination of living ring-opening metathesis polymerization (ROMP) and atom transfer radical polymerization (ATRP). A bromo-containing functional norbornene (NBMBr) was prepared from the Diels-Alder reaction of cyclopentadiene and allyl bromide. The diblock copolymer of 5-(N-carbazolyl methyl)bicycle[2.2.1]hept-2-ene (CbzNB) and NBMBr was successfully prepared using living ROMP and used as a novel macroinitiator [poly(CbzNB-b-NBMBr)] for ATRP. Carbazoyl-containing multi-functional armed copolymer with poly(methyl methacrylate) (PMMA) was prepared by using poly(CbzNB-b-NBMBr) as a macroinitiator for ATRP. Strong fluorescence emissions (370-450 nm) were observed in the low excimer-forming multi-functional armed fluorescent polynorbornenes. The fact is that low excimer-forming carbazole-containing polymeric compound would apparently be favorable in photoconductive materials. The multi-functional armed structure make this compound an attractive candidate for applications as multi-modified hole transport materials in molecular electronic devices. Multi-modification could be further considered to be carried out by using such a functional bromo group at the end of multi-arms.