Natural convection from narrow horizontal plates at moderate Rayleigh numbers

The present work deals with the natural convection flow and heat transfer from a horizontal plate cooled from above. Experiments are carried out for rectangular plates having aspect ratios between φ=0.036 and 0.43 and Rayleigh numbers in the range 290?Ra_w?3.3×10⁵. These values of Ra_w and φ have been selected below those commonly considered in previous research in view of a future application to the design of printed circuit boards. The plates are made of two different metals, copper and steel. The choice of a metal is relevant to the present problem because the plates are heated by means of an electric current. Important variations of the surface temperature are observed along the transverse direction for the steel plates. The surface of the copper plates is almost isothermal because of the high thermal conductivity of the metal.Calculations for a semi-infinite plate are carried out to predict the transverse profiles of the surface temperature and heat flux and to visualize the structure of the flow. Three-dimensional calculations are also used at a qualitative level to observe the changes in the flow structure due to the finite length of the plate. Present results are compared with both previous experimental work and analyses that are based on boundary layer theory. It is shown that analyses for an infinite boundary layer are not completely applicable to the present problem because of its different physics. The most relevant feature of the natural convection flow, which is not predicted by boundary layer analyses, is a thermal plume rising near the center of the plate.Present heat transfer results differ from previous experimental work because of the lower Rayleigh numbers and aspect ratios investigated here. The Nusselt number is found to depend on Ra_wⁿ, with the exponent n=0.17 being lower than most of the values reported in the literature. This comparatively low value is related to the transverse conduction of heat through the air, which becomes increasingly significant as Ra_w approaches zero. It is shown that such a low-Ra_w effect can be accounted for in a physically consistent manner by adding a constant term to the heat transfer correlation. On the other hand, it is found that the Nusselt number does not significantly depend on the aspect ratio in the range of φ investigated contrary to what has been previously reported for wider plates.     

房间空调器高效节能技术分析

本文主要介绍了高效节能型空调器的优化设计，包括选用高效压缩机、增大换热面积，增大风量、管路的合理设计，旨在提高制冷量，降低功耗，提高能效比。     

Optimal control of accelerator concentration for resin transfer molding process

Resin cure following mold filling is an essential element in resin transfer molding. To fabricate a composite part with high dimensional stability and minimize residual stress, uniform resin cure should be achieved. This study considers a three-part resin system composed of epoxy, hardener and accelerator. The cure kinetics can be controlled by the accelerator concentration at the injection gate. A numerical method that can predict degree of cure distribution based on accelerator concentration at the gate was proposed. The degree of cure distribution is obtained by solving the resin flow, heat transfer, accelerator concentration and cure problems sequentially. Utilizing this numerical method, an optimal variation of accelerator concentration during mold filling was sought by solving a constrained optimization problem. The effect of accelerator control on degree of cure distribution was investigated and its validity was examined for two different geometries.     

An Investigation of Vibration Reducing on a Machine Tool

In order to reduce the vibration on a machine tool, more orthogonal experiment schemes have been designed, which are based on the steel balls vibration reducing principle. After experiments the optimal reducing vibration scheme was determined. This kind of vibration reducing scheme is used in steel balls vibration absorber, which can be used to reduce vibration magnitudes of a machine tools under the working conditions, whereby improving machining precision. The suggested experiment method is of useful reference in reducing vibrations on other machine tools too.     

耀江大厦顶层屋面热泵的振动治理

本文通过耀江大厦27层屋面上六台热泵振动治理前后的振动和噪声测试数据的对比，简要阐述了安装在屋面上热泵的振动影响的程度和范围、产生振动影响和固体噪声传递的原因，并介绍了热泵双层隔振的方法和隔振效果。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

Heat transfer mechanism of a swirling impinging jet in a stagnation region

Heat transfer characteristics of a swirling impinging jet have been experimentally examined using a combined particle image velocimetry (PIV) and laser‐induced fluorescence (LIF) technique for simultaneous measurement of velocity and temperature fields. The present study shows that the radial width of the jet stretches with increasing swirl intensity, and that the stretching phenomenon contributes to the maximum local heat transfer coefficient. At the stagnation region, the flow near the heated surface is mixed intermittently by reverse flows toward upstream, and spatial distributions of temperature are correlated with instantaneous velocity vector maps. The dynamic behavior of recirculation zones, attributed to swirl number Sw and impinging distance, mainly determines the turbulent heat transfer at the stagnation region. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(8): 663–673, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10120     

Model for Nanoscopic Domain Formation in Dipalmitoyl-PC/Dilauroyl-PC/Cholesterol Mixture

We describe the lyotropic liquid crystalline phase transitions in the lipid mixture dipalmitoil-PC/dilauroy-PC/cholesterol by 3D spin-1 lattice model. The formation of nanoscale domains with the characteristic size about 300 nm was studied in experiments on confocal fluorescence microscopy (CFM) (G. V. Feigenson and J. T. Buboltz, Biophys. J. 80, 2775 (2001)). The structure parameters of the lamellar vesicle in dipalmitoil-PC-rich phase, corresponding to these regions, are verified by numerical Monte Carlo simulations on the lattice. We point its superconductivity analogy properties at the region of phase stability for composition-dependent nanoscopic region.     

Control of Wind-Induced Self-Excited Oscillations by Transfer of Internal Energy to Higher Modes of Vibration. II: Application to Taut Cables

In Part I of this paper, a theoretical basis is presented using a two-degrees-of-freedom model. In this second part of the study, the passive control and the two types of semiactive controls introduced in Part I are examined numerically for a taut cable experiencing wind-induced galloping motion. The passive and the semiactive control schemes for taut cables show a good similarity with the results obtained for the two-degrees-of-freedom model. The potential of using these control schemes in practical applications to flexible structures is demonstrated.     

压电振子径厚耦合振动的二维等效电路研究

提出了一种轴向极化压电圆环和圆片的径厚二维耦合等效电路模型。应用这一模型分析了它们的耦合振动,比较了不同尺寸比例下耦合振动与单一模式振动的异同,发现这种方法比一维等效电路方法能在较宽尺寸范围内更准确的分析压电振子的振动问题。有限元计算和试验测量结果验证了这一模型对压电振子频率计算的准确性。