单参数Wilson方程预测C_9-DMP体系汽液平衡

根据实测γ~∞_1用单参数Wilson方程预测均三甲苯-DMP和偏三甲苯-DMP二元体系汽液平衡,并推算均三甲苯-偏三甲苯-DMP三元体系的汽液平衡,与实测数据比较,均获得良好结果。     

Preparation of fluoroacrylate nanocopolymer by miniemulsion polymerization used in textile finishing

Latex based on fluoroacrylate (TAN) and other comonomers was prepared via miniemulsion polymerization in the presence of stearyl trimethyl ammonium chloride (STAC) and 2, 2′‐azobis (2‐amidinopropane) dihydrochloride (ABAP) as a water soluble initiator. Light transmittance studies demonstrated that the light transmittance of prepared emulsions increases with the amount of TAN, STAC, cosolvent DPM, and hydrophobe DM. Given suitable reaction temperature and quantities of TAN, STAC, DPM, and DM, a copolymer emulsion of fluoroacylate with a particle size of 50 nm was produced. The water repellency tested on polyester fabrics displayed greater effectiveness than that of commercial products with higher fluorine content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1466–1472, 2004     

Simulation studies on the fuel electrode of a H2---O2 polymer electrolyte fuel cell

The macro-homogeneous porous electrode theory is used to develop a model which describes the catalyst layer of the hydrogen electrode formed by catalyst particles that are bonded to the membrane. The water transport in the catalyst layer and polymer electrolyte membrane is considered. The effects of catalyst layer structure parameters such as polymer volume fraction, catalyst layer thickness, platinum loading and reactant gas humidity as well as CO poison on the hydrogen electrode behavior are examined. The results show that the catalyst layer thickness has a significant effect on the electrode performance. A thicker catalyst layer will result in a larger ohmic voltage loss and higher catalyst cost. The optimal polymer volume fraction and catalyst layer thickness are 0.5 and 1.5–4 μm, respectively, for this electrode. An optimal platinum surface coverage on carbon need not exceed 20% (20 wt% Pt/C). Larger platinum coverage will increase the cost, but only slightly enhance the electrode performance.     

工业循环冷却水成套节水新技术在天津石化乙烯厂的应用

为解决天津地区水资源短缺的现状，通过应用先进的水处理药剂及自动监控技术，在天津石化公司乙烯厂成功地建成了高浓缩倍率冷却水处理技术示范工程，系统浓缩倍率从3倍提高到5倍以上，年节水量超过60万t。     

建筑供排水用聚丙烯管道(PP-R)特性简析

PP -R管道具有质轻、连接方便、良好耐热性和较小导热系数、耐腐蚀且管道阻力小等优点 ,属绿色产品 ,本文对施工过程中就PP -R管与混凝土的粘结不密、抗紫外性能差等问题提出了相应的处理措施     

莫莱石－堇青石滤料滤池在生产上的应用

本文对景德镇市黄泥头水厂进行了单层莫－堇滤料滤池和双层莫－堇－煤滤料滤池的生产性试验。试验结果表明：单层莫－堇滤池和双层莫－堇－煤滤池的周期产水量分别是单层砂滤池和双层砂－煤滤池的１．４倍和１．５倍，而且前两种滤池的出水水质优于后两种滤池。     

龙游黄铁矿灵山东部锌硫矿石选矿研究

提出抑制锌硫首先脱除石墨，铜铅混选及分离，锌硫化先浮选方案，获得了铅、锌、硫三种精矿产品，选矿指标较为理想。合理的利用了井下酸性水，降低了选矿成本和对环境的污染。     

活性炭吸附法处理麦麸膳食纤维废水的研究

采用活性炭吸附的方法来处理麦麸膳食纤维废水。实验结果表明,当活性炭的投入量为160 g/L,接触时间为20 m in,温度为55℃,pH值在小于5的条件下能有效处理该废水,CODC r的去除率最高达96.89%,BOD5的去除率最高达96.61%。     

Long‐term water uptake behavior of natural fiber/polypropylene composites

Composites of different natural fibers and polypropylene were prepared and their long‐term water absorption behaviors were studied. Wood flour, rice hulls, newsprint fibers, and kenaf fibers (at 25 and 50% by weight contents) were mixed with polypropylene and 1 and 2% compatibilizer, respectively. Water absorption tests were carried out on injection‐molded specimens at room temperature for 5 weeks. Measurements were made every week and water absorption was calculated. Water diffusion coefficients were also calculated by evaluating the water absorption isotherms. Results indicated a significant difference among different natural fibers, with kenaf fibers and newsprint fibers exhibiting the highest and wood flour and rice hulls the lowest water absorption values, respectively. The difference between 25 and 50% fiber contents for all composite formulations increased at longer immersion times. Water diffusion coefficients of the composites were found to be about 3 orders of magnitude higher than that of pure PP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Fenton试剂处理苯酚和甲醛废水的研究

用H2O2同Fe^2 结合的Fenton试剂处理有机废水是一种经典的催化氧化法，这种方法适合于处理废水中高浓度、难降解的有机物质。主要研究了Fenton试剂处理含苯酚和甲醛有机废水样的反应机理和影响因素，试验结果表明：废水中苯酚和甲醛的去除率均可达到95％以上，COD去除率达到85％以上，表明用Fenton法处理含苯酚和甲醛的有机废水是一种非常有效的方法。