生物流化床预处理黄浦江原水中试研究

对采用悬浮填料的生物流化床原水预处理技术进行了探讨。分析了自然挂膜条件下的工艺启动过程。在8个工况条件下，流化床对污染物的去除效果。中试运行表明；在温度适谊，停留时间为60min，填料填充率为50%条件下，氨氮平均去除效率达到77.6%。氨氮的比表面去除负荷与温度线性相关。相关系数为0.911;CODMn平均去除率为6.5%。中试装置在温度10.6℃条件下，重启动需要4d，即对污染物有较好的去除效果；由于填料的完全流化，池体内溶解氧传质效率高，出水接近饱和溶解氧；进出水浊度变化不大。填料和池体本身不会积泥，不需反冲洗。     

Chemical modification of hemp,sisal, jute,and kapok fibers by alkalization

Plant fibers are rich in cellulose and they are a cheap, easily renewable source of fibers with the potential for polymer reinforcement. The presence of surface impurities and the large amount of hydroxyl groups make plant fibers less attractive for reinforcement of polymeric materials. Hemp, sisal, jute, and kapok fibers were subjected to alkalization by using sodium hydroxide. The thermal characteristics, crystallinity index, reactivity, and surface morphology of untreated and chemically modified fibers have been studied using differential scanning calorimetry (DSC), X‐ray diffraction (WAXRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM), respectively. Following alkalization the DSC showed a rapid degradation of the cellulose between 0.8 and 8% NaOH, beyond which degradation was found to be marginal. There was a marginal drop in the crystallinity index of hemp fiber while sisal, jute, and kapok fibers showed a slight increase in crystallinity at caustic soda concentration of 0.8–30%. FTIR showed that kapok fiber was found to be the most reactive followed by jute, sisal, and then hemp fiber. SEM showed a relatively smooth surface for all the untreated fibers; however, after alkalization, all the fibers showed uneven surfaces. These results show that alkalization modifies plant fibers promoting the development of fiber–resin adhesion, which then will result in increased interfacial energy and, hence, improvement in the mechanical and thermal stability of the composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2222–2234, 2002     

福建三钢焦化废水处理工艺的改造

通过对福建三钢煤化工有限公司废水处理系统生物脱氮工艺的改造，使出水水质达到国家规定的一级排放标准。同时，对焦化废水处理工艺流程、设备及工艺参数等方面进行了调整和改进，为焦化废水生物脱氮工艺的设计和运行提供了借鉴。     

新一代水管式沉降仪控制模块的研制

新一代低功耗水管式沉降仪控制模块是基于16单片机MSP430F5436为处理器的低功耗装置.该文详细介绍了其硬件结构和工作原理,分别从电源系统、电磁阀控制电路、控制流程、数据采集等部分阐述了其特点,诠释了水管式沉降仪控制模块在人机交互、工作稳定性等多方面所具备的优势.新一代水管式沉降仪控制模块已在实际工程中得到了成功应用,其稳定性和精确性为大坝监控系统提供了准确的实时数据.     

A water‐developable negative photoresist based on the photocrosslinking of N‐phenylamide groups with reduced environmental impact

A water‐developable negative photoresist based on the photocrosslinking of N‐phenylamide groups was prepared by the copolymerization of 4‐styrenesulfonic acid sodium salts (SSS) with N‐phenylmethacrylamide (copolymer A) or p‐hydroxy‐N‐phenylmethacrylamide (copolymer B), and its properties such as solubility changes, photochemical reaction, and photoresist characteristics were studied. The copolymer containing a relatively higher amount of SSS units was soluble in water. Solubility changes of the copolymers in the various buffer solutions of pH 4 ～ 11 and in water upon irradiation were observed by the measurement of insoluble fraction. The copolymers were soluble in water before irradiation, whereas they became insoluble upon irradiation with the UV light of 254 nm. The photochemical reaction of the copolymer studied by the UV and IR absorption spectroscopies indicated that a photo‐Fries rearrangement was favored for copolymer A, whereas a photocrosslinking reaction was predominate for copolymer B. Resist properties of the copolymers were studied by measurement of the normalized thickness and by development of the micropattern. Negative tone images with a resolution of 1 μm were obtained with these materials that have a sensitivity (D) of ～ 1100 mJ/cm² with an aqueous developing process.© 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1172–1180, 2002     

动车水箱安装座的强度计算和结构改进

为使动车上的水箱安装座具备足够的强度,以保证连接的可靠性,利用三维实体建模并用Hyper Works对水箱安装座进行有限元计算;依据EN 12663:2010标准对水箱安装座进行强度校核并针对不满足强度要求的部分进行结构改进.结果表明:改进后的模型设计能够满足EN 12663:2010的标准;CAE软件的应用为水箱安装座的结构设计提供参考.     

利用A/O技术处理己内酰胺生产废水的研究

探讨采用先进的A/O(厌氧菌 /好氧菌 )生物脱氮技术对己内酰胺生产废水进行处理的工作机理和工艺设计方法 ,分析了温度、溶解氧、pH值、进水碳氮比等参数对生物脱氮工艺过程的影响 ,并对其关键技术进行了研究     

硅整流元件纯水冷却系统换热设备的化学清洗

介绍了硅整流元件的纯水冷却系统换热设备化学清洗中药剂的评定筛选原则。质量标准，清洗工艺等。并对其清洗效果加以评定。     

水性聚氨酯的合成及其改性的研究

研究了 n NCO/n OH、扩链剂 ( BD)及二羟甲基丙酸 ( DMPA)的含量对水性聚氨酯合成及涂膜性能的影响 ,确定了较佳的配方。并利用甲基丙烯酸酯类单体合成聚氨酯 -丙烯酸酯共聚复合乳液来改善水性聚氨酯的性能     

电镀工艺的水质控制

阐述电镀配液用水和清洗用水的水质要求和控制指标。