Stress-deformable state of isotropic double curved shell with internal cracks and a circular hole

This work is devoted to the stress–strain state of isotropic double curved shell with defect system. The construction is weakened by two non-through thickness (internal) cracks of different length and by a circular hole located between cracks. In this study we use the line-spring model. Within the framework of this model cracks are modeled as mathematical cuts of shell’s middle surface. This leads to a two-dimensional problem. The problem is reduced to a system of eight boundary integral equations. To ensure the uniqueness of solution an additional equation is added. In the numerical solution of the problem special quadrature formulas for singular integrals of Cauchy type and the finite difference method are applied. The influence of defects on each other for double curved shell has been investigated. The given theoretical results can be used for the calculation of structural elements with holes, cracks on the strength and fracture toughness in various branches of engineering.     

Two-level intelligent modeling method for the rate of penetration in complex geological drilling process

The rate of penetration (ROP) model is of great importance in achieving a high efficiency in the complex geological drilling process. In this paper, a novel two-level intelligent modeling method is proposed for the ROP considering the drilling characteristics of data incompleteness, couplings, and strong nonlinearities. Firstly, a piecewise cubic Hermite interpolation method is introduced to complete the lost drilling data. Then, a formation drillability (FD) fusion submodel is established by using Nadaboost extreme learning machine (Nadaboost-ELM) algorithm, and the mutual information method is used to obtain the parameters, strongly correlated with the ROP. Finally, a ROP submodel is established by a neural network with radial basis function optimized by the improved particle swarm optimization (RBFNN-IPSO). This two-level ROP model is applied to a real drilling process and the proposed method shows the best performance in ROP prediction as compared with conventional methods. The proposed ROP model provides the basis for intelligent optimization and control in the complex geological drilling process.     

Prediction of rock mass P wave velocity using blasthole drilling information

In this paper, the development of the models for the prediction of rock mass P wave velocity is presented. For model development, the database of 53 cases including widely used and recorded drilling parameters and P wave velocity was constructed from the field studies conducted in 13 open pit lignite mines. Both conventional linear, non-linear multiple regression and Adaptive Neuro Fuzzy Inference System (ANFIS) were used for model development. Prediction performance indicators showed that ANFIS model presented the best performance and it can successfully be used for the preliminary prediction of P wave velocities of rock masses.     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

关于天然气水合物钻采工艺技术进展的研究

目前全球正面临着前所未有的能源危机，天然气水合物由于储量大、能量密度高而将成为一种诱人的新型能源。天然气水合物主要存在于冻土带和海洋，在地下处于低温和高压状态，以现有的技术，钻井和开采都存在很大的困难。简要介绍了天然气水合物的性质及储量，阐述了天然气水合物钻井的六个挑战及目前国外天然气水合物的两种钻探方法；同时阐述了以热力法、降压法和化学试剂注入法为主的天然气水合物开采方法，并针对天然气水合物钻采技术现状指出了下一步的研究方向。     

大位移井钻柱振动规律研究与应用

在大位移井钻井工程中钻柱受着各种振动，当各种振动共振时，钻柱承受着非常大的动载，很容易受损，同时，钻柱的振动影响着井壁的稳定，严重威胁着井下的作业安全。以大位移井近井底的钻柱为研究对象，分析了钻柱振动行为所遵循的规律。采用线性分析法，获得了大位移井钻柱横向振动和扭转振动的频谱方程。同时获得了钻柱各种共振频率的分布。经分析表明：大位移井钻柱的横向振动和扭转振动的共振频率与实际钻井转速非常接近，应合理选择转速以减小钻柱共振的发生。文章的分析研究为大位移井钻柱动态行为的研究提供了理论依据。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

面积坐标法构造含转角自由度的四结点膜元

以四边形面积坐标作为工具,构造了两个含转角自由度的广义协调四边形单元AQ4和lAQ4。它们通过强式分片检验,与同类单元相比,具有很高的计算精度,能消除梯形闭锁现象,有很强的抗网格畸变的能力。     

钻井参数仪的模块化设计方法研究

文章以模块化设计原理为基础，讨论了钻井参数仪的模块划分，模块化设计准则和主要设计内容。采用模块化设计方法、现场设备网络的开放网络和现场总线解决方案设计的钻井参数仪，具有传输信号稳定、可靠性高、抑制噪声能力强、组建现场网络成本低等特点。     

关于我国石油钻机技术的现状及其研发思考

介绍了我国石油钻机的技术现状,在肯定我国石油钻机发展所取得成绩的同时,指出我国石油钻机整体技术与国外钻机技术的差距,提出要把石油钻机作为国家战略装备来对待,加快我国石油钻机新技术、新产品研发工作,以满足我国石油工业发展的需要。