一种新型注入剖面组合测井仪及其应用

为了提高注入剖面测井的准确性，研制了一种新型注入剖面组合测井仪。该仪器由流量处理单元、伽马处理单元、井温处理单元、磁性定位处理单元、调制式传输、电源电路六部分组成。一次下井可同时测取流量、伽马、井温、磁性定位四组参数。具有测取资料精度高、单芯电缆传输、流量可单点测量也可连续测量以厦现场监测和维修方便等特点。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

高抗挤厚壁套管的性能及应用效果评价

中原油田套管损坏的主要原因是现有套管强度不够,无法抵抗盐膏层段的巨大外挤力。开发了TP130TT型高抗挤厚壁套管,其强度能很好地抵抗盐膏层巨大外挤力。实验室试验表明,各项性能指标达到了设计要求,现场使用取得了很好的效果,解决了中原油田盐膏层段套管强度不足的难题。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

自动力套管补贴加固技术及其在B125井的应用

随着油田开发时间的延长，油水井井下套管的损坏将越来越严重，套管故障井将越来越多，为了恢复套损井生产，将套管损坏所造成的损失降到最低，在配套波纹管补贴，水动力补贴，爆炸补贴等专门修套技术的基础上，通过认真调查研究，又配套了操作方便简单，适用套管损坏类型广的自动力套管补贴加固技术，使各种套管变形，套管断错（错开没有位移或位移量不大时）、套管破裂，误射孔井段封堵，已射开水层封堵等修井作业的难度进一步降低，从而进一步提高了修复井综合开发经济效益。     

TP130TT高抗挤套管研究与应用

为了提高盐层段固井质量 ,中原油田研究开发了 TP130 TT高抗挤套管 ,性能试验评价表明 ,其抗挤强度超过 16 0 MPa,并给出了其固井质量评价标准。在中原油 346口井中的应用表明 ,该套管有效地解决了盐层段套管损坏问题 ,延长了油气水井寿命 ,经济效益和社会效益显著。     

Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.