Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

应用时频分析方法辨识时变系统的模态参数

应用Gabor展开及Hilbert变换进行时变线性系统模态参数的辨识。利用非平稳信号的Gabor变换将结构响应信号表示在时频面上，并通过Gabor展开重构分离模态分量，建立每一阶模态的时变线性模型。对单模态时变线性模型应用Hilbert变换来辨识随时间变化的模态频率和阻尼。通过对刚度和阻尼慢变的两自由度系统模态参数的仿真辨识验证辨识方法的有效性。仿真结果表明：本文方法为时变线性系统的模态参数辨识提供了一条新的途径。     

集中药包与条形药包爆破漏斗及抛掷堆积研究

把集中药包拉成条形药包之后，其爆破漏斗变化有多大?条形药包能否改善抛掷堆积?可否用集中药包的爆破漏斗参数(n、R、R’、P)及经验方法来设计条形药包的爆破漏斗?本试验研究将回答这些问题。     

HP700圆锥破碎机动锥的有限元分析

对HP700圆锥破碎机的主要部件动锥建立了有限元分析模型，用ANSYS软件对动锥进行了有限元强度和刚度分析，结果输出了动锥分布及变形图，对圆锥破碎机的结够设计提供了依据。     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

高发泡聚乙烯阻燃初探

根据聚合物燃烧现象和一般阻燃机理寻求研究高发泡聚乙烯的阻燃方法和阻燃剂。研究结果表明:只有对添加型阻燃剂三元并用,方能不降低高发泡聚乙烯的物性,制得较为理想的高发泡聚乙烯自熄型制品。     

Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

A semi-analytic boundary element method for parabolic problems

A new semi-analytic solution method is proposed for solving linear parabolic problems using the boundary element method. This method constructs a solution as an eigenfunction expansion using separation of variables. The eigenfunctions are determined using the dual reciprocity boundary element method. This separation of variables-dual reciprocity method (SOV-DRM) allows a solution to be determined without requiring either time-stepping or domain discretisation. The accuracy and computational efficiency of the SOV-DRM is found to improve as time increases. These properties make the SOV-DRM an attractive technique for solving parabolic problems.     

复射线展开法分析圆柱面对平面波散射的精度问题

讨论了用复射线展开法计算圆柱面对入射平面波散射时的计算误差特性，提出了控制其计算精度的复射线展开参数选择方法，证实了通过恰当选择展开参数可以有效地提升计算精度、实现误差控制。