Thermal and transport properties of as-grown Ni-rich TiNi shape memory alloys

Electrical resistivity, Seebeck coefficient, specific heat and thermal conductivity measurements on the Ti_50−xNi_50+x (x = 0.0–1.6 at.%) shape memory alloys are performed to investigate their thermal and transport properties. In this study, anomalous features are observed in both cooling and heating cycles in all measured physical properties of the slightly Ni-rich TiNi alloys (x ≤ 1.0), corresponds to the transformation between the B19′ martensite and B2 austenite phases. Besides, the transition temperature is found to decrease gradually with increasing Ni content, and the driving force for the transition is also found to diminish slowly with the addition of excess Ni, as revealed by specific heat measurements. While the signature of martensitic transformation vanishes for the Ni-rich TiNi alloys with x ≥ 1.3, the characteristics of strain glass transition start to appear. The Seebeck coefficients of these TiNi alloys were found to be positive, suggesting the hole-type carriers dominate the thermoelectric transport. From the high-temperature Seebeck coefficients, the estimated value of Fermi energy ranges from ∼1.5 eV (Ti_48.4Ni_51.6) to ∼2.1 eV (Ti₅₀Ni₅₀), indicating the metallic nature of these alloys. In addition, the thermal conductivity of the slightly Ni-rich TiNi alloys with x ≤ 1.0 shows a distinct anomalous feature at the B19′ → B2 transition, likely due to the variation in lattice thermal conductivity.     

Design criterion for fatigue strengthening of riveted beams in a 120-year-old railway metallic bridge using pre-stressed CFRP plates

This study presents a design criterion developed for fatigue strengthening of a 120-year-old metallic railway bridge in Switzerland and presents a pre-stressed un-bonded reinforcement (PUR) system developed to apply the strengthening. The PUR system uses carbon fiber reinforced polymer (CFRP) plates; however, unlike conventional pre-stressed CFRP reinforcement methods, preparation of the existing metallic bridge surface is not required. This decreases the time required for on-site strengthening procedures. The principle of the constant life diagram (CLD) and two fatigue failure criteria (Johnson and Goodman) are described. Analytical formulations are developed based on the CLD method to determine the minimum CFRP pre-stress level required to prevent fatigue crack initiation. The PUR system uses an applied pre-stress force to reduce the mean stress level (and stress ratio) to shift an existing fatigue-susceptible metallic detail from the ‘at risk’ finite life regime to the ‘safe’ infinite life regime. The applied CLD method is particularly valuable when the stress history of the detail is not known and it is difficult to assess the remaining fatigue life. Moreover, it is shown that the currently adopted approach in many structural codes which emphasizes stress range as the dominant parameter influencing fatigue life are non-conservative for tension–tension stress patterns (i.e., stress ratios of 0 < R < 1). Analyses show that the modified Johnson formula accurately reflects the combined effect of stress range, mean stress level, and material properties, and offers a relatively easy design procedure. Details of a retrofit field application on members of a riveted wrought iron railway bridge are given. A wireless sensor network (WSN) system is used for long-term monitoring of the on-site CFRP stress levels and temperature of the retrofitted details. WSN measurements indicate that increases in ambient temperature result in increased CFRP pre-stress levels.     

Hybrid make-to-stock and make-to-order systems: a taxonomic review

Production planning and control (PPC) systems that employ aspects from both make-to-order (MTO) and make-to-stock (MTS) production control are known as hybrid MTS/MTO systems. While both MTO and MTS separately have been studied extensively, their combined use has received less attention. However, the literature on this topic is growing and this paper shows that the review performed in this paper is an important addition to the field. We categorise relevant literature according to a novel taxonomy and show that hybrid MTS/MTO production control can be used in different contexts. In addition, an overview of the modelling techniques and methods used in these papers is provided. Based on the reviewed literature, relevant research questions and directions for future research are identified. Finally, it is shown that hybrid MTS/MTO production control is prevalent in practice by discussing research with industrial applications. The paper contains an overview of research on hybrid MTS/MTO production control to be used as reference for researchers active in the field, and provides managerial insights and directions for future research on this topic.     

The Role of Cell Cycle Regulators in Cell Survival—Dual Functions of Cyclin-Dependent Kinase 20 and p21Cip1/Waf1

The mammalian cell cycle is important in controlling normal cell proliferation and the development of various diseases. Cell cycle checkpoints are well regulated by both activators and inhibitors to avoid cell growth disorder and cancerogenesis. Cyclin dependent kinase 20 (CDK20) and p21^Cip1/Waf1 are widely recognized as key regulators of cell cycle checkpoints controlling cell proliferation/growth and involving in developing multiple cancers. Emerging evidence demonstrates that these two cell cycle regulators also play an essential role in promoting cell survival independent of the cell cycle, particularly in those cells with a limited capability of proliferation, such as cardiomyocytes. These findings bring new insights into understanding cytoprotection in these tissues. Here, we summarize the new progress of the studies on these two molecules in regulating cell cycle/growth, and their new roles in cell survival by inhibiting various cell death mechanisms. We also outline their potential implications in cancerogenesis and protection in heart diseases. This information renews the knowledge in molecular natures and cellular functions of these regulators, leading to a better understanding of the pathogenesis of the associated diseases and the discovery of new therapeutic strategies.     

Static and free vibration analysis of functionally graded plates based on a new quasi-3D and 2D shear deformation theories

In this study, two dimensional (2D) and quasi three-dimensional (quasi-3D) shear deformation theories are presented for static and free vibration analysis of single-layer functionally graded (FG) plates using a new hyperbolic shape function. The material of the plate is inhomogeneous and the material properties assumed to vary continuously in the thickness direction by three different distributions; power-law, exponential and Mori–Tanaka model, in terms of the volume fractions of the constituents. The fundamental governing equations which take into account the effects of both transverse shear and normal stresses are derived through the Hamilton's principle. The closed form solutions are obtained by using Navier technique and then fundamental frequencies are found by solving the results of eigenvalue problems. In-plane stress components have been obtained by the constitutive equations of composite plates. The transverse stress components have been obtained by integrating the three-dimensional stress equilibrium equations in the thickness direction of the plate. The accuracy of the present method is demonstrated by comparisons with the different 2D, 3D and quasi-3D solutions available in the literature.     

Seawater-softening process through formation of calcite ooids

Conventional water-softening processes usually involve the exchange of Na⁺ ions for Ca²⁺ and Mg²⁺ using commercial or synthesized ion exchangers. The differences in chemical compositions of the ooids can be attributed to the formation in different environments. In this paper, ooid grains form inside assembled semi-pilot softening unit through a continuous chemical process involving reaction between bicarbonate ions and added lime using natural seawater. Our sample of Mediterranean seawater has low Mg²⁺/Ca²⁺ ratio (1.98%) within the range chemically favorable for precipitation of low-Mg calcite ooids. Precipitation of calcite occurs around pure quartz sand grains which act as nucleation points (the bed required for sand vessel is 1.65 l). The shape of the sand grains controls the overall external morphology of the resulting ooids; they vary in size from 0.5 to 3.0 mm and have a high degree of polish due to surface abrasion caused by continuous agitation inside the softening system. Calcite ooid grains (1.53 kg) formed within the seawater-softening unit every 18 days have many of the ooid features formed in marine environments. Ooids grow to a significant size, at a rate of about 0.17 mm of one layer thickness per day inside the softening unit. The average weight percent of calcite precipitate is 35.48% after 18 days, at 10 °C, 60 l/min and pH 9.0. The pellets comprise mainly CaCO₃ and SiO₂ and some metal ions which may substitute for calcium ions in calcite are present only in trace amounts of the total composition.     

浅谈氯碱氢的一种深度脱水工艺

概述了氢的主要工业生产方法和实际应用,详细介绍了氯碱氢三级脱水工艺过程,并运用在线分析手段,准确显示了干燥过程中的氯碱氢水分含量变化规律。     

Hydroxyapatite/tricalcium silicate composites cement derived from novel two-step sol-gel process with good biocompatibility and applications as bone cement and potential coating materials

Tricalcium silicate (C₃S) and hydroxyapatite (HAp) composites were fabricated through the sol-gel process. The aim of this research is to improve the biocompatibility of C₃S through HAp addition and study the potential of using this as coating materials. The composites (HAp/C₃S) were characterised by Fourier transform infrared spectrometry, thermal gravity-differential thermal analysis and X-ray diffraction. The working and setting times of cement pastes were tested using Gillmore needle. Mechanical properties were examined by nanoindentation and material testing system. In vitro biocompatibility of the materials were studied by cell attachment and viability of L929 and MG-63 cells. HAp/C₃S as a coating material on gelatin film were measured with the surface roughness and imaged by scanning electron microscope. With the addition of HAp, no undesirable free CaO was detected with the synthesis by the sol-gel preparation. The pH values of HAp added groups were between 7.54 and 8.76, which were much lower than pure C₃S group (pH?=?11.75). For in vitro studies, the presence of HAp could effectively enhance the cell attachment and viability of both L929 and MG-63 cells grown in the extract or directly on the composites. However, the mechanical properties of the composites were impaired as compared to pure C₃S. Lastly, HAp/C₃S cement could be evenly coated on gelatin film. HAp is successfully demonstrated to improve C₃S biocompatibility with this new composites HAp/C₃S. C-75 (75% C₃S and 25% HAp), in particular, has good biocompatibility, relatively high compressive strength and can be uniformly coated onto gelatin film. Thus, C-75 is a promising material for further investigation as a coating on other biopolymers.     

A new metaheuristic for optimization: Optics inspired optimization (OIO)

Due to the law of reflection, a concave reflecting surface/mirror causes the incident light rays to converge and a convex surface/mirror causes the light rays to reflect away so that they all appear to be diverging. These converging and diverging behaviors cause that the curved mirrors show different image types depending on the distance between the object and the mirror. We model such optical phenomena metaphorically into the searching process of numerical optimization by a new algorithm called optics inspired optimization (OIO). OIO treats the surface of the numerical function to be optimized as a reflecting surface in which each peak is assumed to reflect as a convex mirror and each valley to reflect as a concave one. Each individual is assumed to be an artificial object (or light point) that its artificially glittered ray is reflected back by the function surface, given that the surface is convex or concave, and the artificial image is formed (a candidate solution is generated within the search domain) based on the mirror equations adopted from physics of optics. Besides OIO, we introduce different variants of it, called ROIO (Rotation based OIO), and COIO (Convex combination based OIO) algorithms and conduct an extensive computational effort to find out the merit of the new algorithms. Our comparisons on benchmark test functions and a real world engineering design application (i.e., optimization of a centrifuge pump) demonstrate that the new algorithms are efficient and compete better than or similar to most of state of the art optimization algorithms with the advantage of accepting few input parameters.