新疆叶尔羌河中游渠首工程地基处理设计

叶尔羌河洪水动态规律极为复杂,以其极高的起涨速率、异常的高洪峰值闻名于世。中游渠首地基是粘粒极少、极松散的粉细沙层。针对其特点,采用振冲挤密砂石桩、防渗防冲连续墙、抗冲柔性土工布金属网格石笼等综合处理措施进行设计。     

柴达木盆地北缘中生界剥蚀厚度恢复

认为地层剥蚀厚度能否根据压实规律来恢复,其决定因素并非是新沉积层厚度是否大于剥蚀厚度;当不整合面以上新沉积层对不整合面以下老地层施加的压力大于被剥蚀地层(剥蚀前)对不整合面以下老地层施加的压力时,不整合面以下老地层的压实规律被破坏,无法用声波时差法恢复剥蚀厚度,否则可以恢复。据此,以用声波测井资料恢复的地层剥蚀厚度为依据,结合未被剥蚀地层厚度趋势延伸法、盆地构造演化分析法,对柴达木盆地北缘中生界剥蚀厚度进行了恢复,认为柴达木盆地北缘剥蚀量从西向东增大,昆特依坳陷和冷湖构造带的剥蚀量(约500m)大于其东部南八仙、鱼卡等地区(约100m),潜西—冷湖四号地区剥蚀量最大(最大可超过1400m)。图5参4(梁大新摘)     

Y对轴承钢上激光熔覆FeCoCrNi涂层结构和冲蚀磨损的影响

以激光熔覆方法在轴承钢上制得FeCoCrNi-xY高熵合金涂层,并对其处于气体环境中的耐高温冲蚀性进行了测试。研究Y对涂层结构和冲蚀磨损的影响。研究结果表明：随着Y增大,蜂窝形组织开始减少直到全部消失,生成了许多尺寸较小的M颗粒,形成了粒径更小以及分布形态更均匀的Y化物组织。提高Y的加入量后,涂层发生了硬度先减小再增大势,测试得到的硬度值介于720-960 HV范围内。当逐渐提高冲蚀角后,FeCoCrNi-xY涂层发生了冲蚀磨损率持续增大。FeCoCrNixY涂层获得了高于轴承钢的硬度,呈现明显的脆性特点。对FeCoCrNi-0.3Y涂层冲蚀形成了深度更大的犁沟,达到了更高的冲蚀磨损率。当温度提高后,磨损率同样呈现增大现象,不过变化幅度较低。各攻角下的涂层磨损形式并未受到温度的明显影响。     

Erosion of glacial till from the St. Clair River (Great Lakes basin)

Variations in water level observed in Lakes Michigan and Huron during the last few decades have motivated a comprehensive study involving climatic, hydrologic and hydraulic factors organized by International Joint Commission of the Great Lakes. It has been submitted, among other possible causes, that changes in conveyance in the St. Clair River could be contributing to the lowering of the upper Great Lakes water level. Sediment transport processes, in particular bed scour and erosion, can affect significantly a river's conveyance, thus creating the need to assess the erodibility properties of the river bed. To this end, laboratory tests were performed in order to obtain the value of the critical shear stress needed to erode the cohesive fraction of the bed sediment material, known as glacial till, from the St. Clair River. Different flows with increasing velocities were run up to the point where initial sediment erosion could be observed. Through detailed near-bed velocity measurements using a laser Doppler velocimetry (LDV) system, a value of 4.2 N/m² was obtained as the critical shear stress for the erosion of glacial till. A threshold for the critical shear stress for erosion of similar cohesive sediments was also found and expressed in dimensionless form. These results could be used in combination with mathematical models to estimate the risk of scour and erosion at locations where the glacial till is exposed to both strong currents and flow forces induced by the large navigation vessels commonly observed along the course of the St. Clair River.     

Synthesis and characterization of a novel soil stabilizer based on biodegradable poly(aspartic acid) hydrogel

A novel soil stabilizer based on poly-amino acid - polyaspartic acid (PASP) and its copolymer which modified by xanthan gum (XG) was studied to increase soil particle compressive strength and resistance to wind erosion. Due to its unique property, the stabilizer aggregated individual soil particles and formed crust. The sample compressive strength increased from 0.175 to 0.612 MPa and the wind erosion modulus reduced from 22.43 to 10.56 g·m⁻²·min⁻¹ after the 1% PASP hydrogel was applied by 1.67 Lm⁻² (1 cm of crust). The soil water content was higher than the control due to the polymer’s excellent water-retaining property. The polymer had no negative influence on seed germination and growth. The biodegradability experiment showed that PASP was easy to biodegrade and therefore it was safe to apply in the field. This work was presented at 13 ^th YABEC symposium held at Seoul, Korea, October 20–22, 2007.     

Chemical sputtering of deuterated carbon surfaces at various surface temperatures

The chemical sputtering of deuterated amorphous carbon (a-C:D) surfaces irradiated by 1-50 eV deuterium atoms at surface temperatures between 300 and 1000 K was studied using classical molecular dynamics. A quasi-stationary state was reached by cumulative bombardment for each energy and temperature. Results were compared with available experimental data and previous modeling results and the applicability of molecular dynamics for thermally generated processes was discussed. An attempt is made to correct the absence of the thermally stimulated desorption/degassing of hydrogen from the MD simulations, which evolve at the longer time scales.     

箱形涵洞对河床水沙特性影响的试验研究

以漳河的穿河涵洞为对象,采用物理模型的方法,就3年一遇和50年一遇洪水工况时箱形涵洞所在河道的沿程水位、上下游各断面流速及其下游河床局部冲淤变形等问题进行了试验观测,探讨了箱形涵洞对河床水沙特性的影响。试验表明:在3年一遇和50年一遇洪水工况下,箱形涵洞对上游河床的壅水较少,最大壅水高度分别为0.57m和0.3m;涵洞上游各断面的平均流速较无涵洞时有所减小,且断面横向流速分布曲线更平坦。在迎水面出现了河中心流速较左右岸流速大的现象;在涵洞下游较远的CS8断面的平均流速分别为1.8m/s和3.7m/s,与无涵洞时相差不大;在3年一遇洪水工况下,箱形涵洞洞后能形成Fr=4.52的稳定水跃,使得箱形涵洞下游CS6断面的河床局部冲刷较少,其平均冲刷深度约为0.5m。由此可见,箱形涵洞具有较优的水力条件。     

Numerical Simulation of Tube Erosion in a Bubbling Fluidized Bed with a Dense Tube Bundle

Tube erosion in a bubbling fluidized bed is numerically studied using the Eulerian‐Eulerian method coupled with a monolayer kinetic energy dissipation model. The hydrodynamical simulations are performed under conditions with three different superficial gas velocities. The time‐averaged bubble frequency and bubble rise velocity are calculated to characterize the bed hydrodynamics. The erosion rates of two target tubes are simulated and the influence of the bubble behaviors on erosion rates is evaluated. Compared with the experimental data in the literature, the bubble behaviors are well captured by the simulations. Good agreement between the calculated and measured erosion rates is also obtained for the two target tubes. The bubble behaviors around the tubes have direct impact on the tube erosion. Only small discrepancies in the calculated erosion rates are found when using different particle‐wall restitution coefficients and specularity coefficients.     

Thermal and ablative properties of binary carbon nanotube and nanodiamond reinforced carbon fibre epoxy matrix composites

The thermal and ablative properties of carbon nanotube (CNT) and nanodiamond (ND) reinforced carbon fibre epoxy matrix composites were investigated by simulating shear forces and high temperatures using oxyacetylene torch apparatus. Three types of composite specimens—(i) carbon fibre epoxy matrix composite (CF/Epoxy), (ii) carbon fibre epoxy matrix composite containing 0.1 wt-% CNTs and 0.1 wt-% NDs, and (iii) carbon fibre epoxy matrix composite containing 0.2 wt-% CNTs and 0.2 wt-% NDs—were explored. The ablative response of composites was studied through pre- and post-burnt SEM analysis and further related with thermogravimetric analysis, weight loss profile and thermal conductivity measurements. The novel nanofiller composites showed marked improvement in their thermal and ablative properties. A 22% and 30% increase in thermal conductivity was observed for composites containing 0.1 wt-% CNTs/0.1 wt-% NDs and 0.2 wt-% CNTs/0.2 wt-% NDs respectively. These nanofillers also improved the thermal stability of thermosetting epoxy matrix, and an increase of 13% and 20% was recorded in the erosion rate of composites containing 0.1 wt-% CNTs/0.1 wt-% NDs and 0.2 wt-% CNTs/0.2 wt-% NDs respectively. This improvement is due to the increased char yield produced by the increase in the loading of nanofillers, i.e. CNTs and NDs. Insulation index and insulation to density performance have also been improved due to increased thermal conductivity and char yield.     

碱金属和锌对高炉用SiAlON结合刚玉砖的复合侵蚀

将高炉用SiAlON结合刚玉砖制成外部尺寸为50mm×50mm,内孔尺寸为25mm×25mm的坩埚,分别加入由Na2CO3、K2CO3、ZnO和宝钢高炉现场高炉灰配制的炉渣(其w(Na2O+K2O)=2.75%,w(ZnO)=5.1%)和用K2CO3、ZnO、石墨配制的炉渣(其w(Na2O+K2O)=25%,w(ZnO)=25%),然后分别在还原气氛下于1350℃16h和1100℃40h进行侵蚀试验。将侵蚀后的试样纵向对称剖开,观察渣对试样的侵蚀和渗透情况,进行SEM和EDAX分析。结果表明:碱金属和锌含量不同的两种炉渣对SiAlON结合刚玉砖的侵蚀速度都很小;碱金属侵蚀机理主要是SiAlON与碱蒸气反应生成钾霞石,与渣反应生成铁橄榄石,并参与硅酸盐玻璃相的生成;刚玉颗粒与渣中的FeO、Na2O和K2O反应生成铁铝尖晶石和少量针状β-Al2O3;锌对该砖没有产生明显的化学侵蚀。