压水堆硼稀释事故的计算

一、概述核电厂压水堆的初始过剩反应性是通过控制捧、固体可燃毒物和溶解在主回路冷却剂中的硼酸等三种方式联合控制的。随着反应堆的燃耗和裂变毒物的积累,堆的过剩反应性不断减少,需要通过化容系统,控制硼酸的浓度来进行补偿。如果化容系统发生故障或操作员误操作,就会给回路注入无硼或低于规定浓度的补给水,给反应堆引入正反应性,造成硼稀释事故。按核安全法规的要求,应对换料、冷停堆、热停堆和启动等工况进行计算,并要求在这些     

酒泉盆地青西油田快速钻井技术

酒泉盆地青西地区油层储藏深 ,地层可钻性差 ,钻井过程中存在机械钻速低、井斜不易控制、刺断钻具频繁等问题。为此 ,在近年的钻井实践中 ,采取了优化钻具组合、优选钻头、应用 PDC钻头、强化钻具管理等措施 ,使该区块的钻井速度不断提高 ,钻井周期缩短 ,钻头用量减少 ,从而形成了一套适合该区块的快速钻井技术。     

再造鼓形膨胀器

介绍了本钢不停产安装再造煤气管道鼓形膨胀器的实践，并对制造、安装方法进行了叙述，特别是在结构上采用了独特的构槽密封焊缝和完整的安装程序，保证了实施的安全。     

高炉鼓风机电气控制技术改造

对高炉鼓风机事故原因分析发现，低电压保护动作、二次控制电源断电、电网电压突降是造成风机自动跳闸的主要原因。对风机电气控制技术进行改进，采取了去掉低电压跳闸保护、增设专用二次控制电源、设置瞬时断电延时自启动控制线路等措施，有效地避免了风机故障的发生，年减少经济损失66．13万元。     

液闪测氡中闪烁杯的氡气泄漏

本文简要介绍了液闪测氡中氡气自闪烁杯泄漏的实验结果。实验中对三种玻璃闪烁杯盖的密封性能作了检查,结果表明,这三种闪烁杯均不能满足液闪法测氡中对氡的密封要求。采用一层1mm 厚的橡胶垫片和一层0.01mm 厚的铝化聚脂膜作衬垫,代替原来的聚乙烯或纸板衬垫,解决了其中两种闪烁杯的氡气泄漏问题。建议在使用商品闪烁杯测氡时,应首先检查其对氡的密封性,必要时需采取补救措施,以保证测量结果的可靠性。     

Accidents,often the result of an ‘uncontrolled business process’—a study in the (Dutch) chemical industry

Often companies in the (petro‐) chemical industry claim that all possible countermeasures against potential accidents have been taken and therefore accidents are unforeseeable. In this paper we question this statement by analysing the pre‐warning signals (precursors) preceding a number of industrial accidents. 17 accidents that occurred in the (petro‐) chemical industry have been investigated by exploring FACTS, an accident database containing information about industrial accidents worldwide. This paper will demonstrate that the existence of precursor information could have been used to foresee and even prevent these accidents if a proper control action had been initiated. The accidents are analysed further, according to a control model, which was adapted from that of C. Argyris. It demonstrates the ineffectiveness of several elements of business process control loops and that the so‐called ‘double‐loop learning’ cycle is more important than the ‘single‐loop learning’ cycle if one considers safety improvement. Copyright © 2003 John Wiley & Sons, Ltd.     

Design Errors: Inefficiency or Carelessness of Designer?

Design defects are experienced in many projects; the difference is only in the extent of occurrence. This technical note discusses a design error case in a building project in Nepal, where the designer made the wrong assumptions in roof treatment work for waterproofing as well as for heat insulation purposes. From the investigation of the problem, it was found that the waterproofing polymer was not applied directly over concrete slab top. Use of heavy concrete block as a heat insulation material also helped to increase the leakage problem. The problem evoked loss of prestige for project officials, the design consortium, and the contractor.     

砌筑砂浆达不到设计要求的事故原因分析

从砂浆的配合比、和易性、原材料等对砌筑砂浆达不到设计要求的事故原因进行了分析。     

Analysis of lightning surge propagation in wind farm

Wind power generation is expected to become more important in future distribution systems. Although several prospective reports such as IEC 61400‐24 and NREL SR‐500‐31115 indicate an insulation scheme and grounding design for lighting protection, there still seems to be too few investigations on the problems. This paper therefore discusses lightning surge analysis using a wind farm model with 2 or 10 ideal wind turbines. Changing parameters such as grounding resistance and lightning strike points, several cases were studied. As a result of the analysis using digital simulator ARENE, it is clear that the surge tends to propagate toward the end of a distribution line in a wind farm and there is the possibility of insulation accidents at the other wind turbines when lightning attacks a wind turbine. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(2): 30– 38, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20364