Platinum Binuclear Complexes as Phosphorescent Dopants for Monochromatic and White Organic Light‐Emitting Diodes

Efficient blue‐, green‐, and red‐light‐emitting organic diodes are fabricated using binuclear platinum complexes as phosphorescent dopants. The series of complexes used here have pyrazolate bridging ligands and the general formula C^∧NPt(μ‐pz)₂PtC^∧N (where C^∧N = 2‐(4′,6′‐difluorophenyl)pyridinato‐N,C^2′, pz = pyrazole ( 1 ), 3‐methyl‐5‐tert‐butylpyrazole ( 2 ), and 3,5‐bis(tert‐butyl)pyrazole ( 3 )). The Pt–Pt distance in the complexes, which decreases in the order 1 > 2 > 3 , solely determines the electroluminescence color of the organic light‐emitting diodes (OLEDs). Blue OLEDs fabricated using 8 % 1 doped into a 3,5‐bis(N‐carbazolyl)benzene (mCP) host have a quantum efficiency of 4.3 % at 120 Cd m^–2, a brightness of 3900 Cd m^–2 at 12 V, and Commission Internationale de L'Eclairage (CIE) coordinates of (0.11, 0.24). Green and red OLEDs fabricated with 2 and 3 , respectively, also give high quantum efficiencies (～ 6.7 %), with CIE coordinates of (0.31, 0.63) and (0.59, 0.46), respectively. The current‐density–voltage characteristics of devices made using dopants 2 and 3 indicate that hole trapping is enhanced by short Pt–Pt distances (< 3.1 Å). Blue electrophosphorescence is achieved by taking advantage of the binuclear molecular geometry in order to suppress dopant intermolecular interactions. No evidence of low‐energy emission from aggregate states is observed in OLEDs made with 50 % 1 doped into mCP. OLEDs made using 100 % 1 as an emissive layer display red luminescence, which is believed to originate from distorted complexes with compressed Pt–Pt separations located in defect sites within the neat film. White OLEDs are fabricated using 1 and 3 in three different device architectures, either with one or two dopants in dual emissive layers or both dopants in a single emissive layer. All the white OLEDs have high quantum efficiency (～ 5 %) and brightness (～ 600 Cd m^–2 at 10 V).     

阜阳地区石炭-二叠系煤系烃源岩特征

阜阳地区石炭-二叠系煤系地层发育，但由于勘探程度较低，对该区煤系地层烃源岩的生烃潜力认识不清，严重制约了该区的油气勘探。在已有资料的基础上，通过有机地球化学和有机岩石学方法并结合模拟实验，探讨了该区煤系烃源岩的生烃潜力。研究结果表明阜阳地区石炭-二叠系煤系烃源岩有机质丰度达到中等-好烃源岩标准，有机质类型以腐殖型为主，盆地模拟结果显示阜阳地区石炭-二叠系煤系地层油资源量为（30.47~152.33）×10⁶t，气资源量为（266.7～1333.7）×10⁸m³，展示阜阳地区石炭-二叠系煤系地层具有较好的生油气潜力。     

凉水河污染对土壤和地下水的影响

在凉水河下游取河床底泥及河床下部土样,分析其NH3-N、磷和有机物的变化,发现底泥对NH3-N和磷的去除发挥了很大作用,分别是下部土壤吸附量的10倍和1倍多;土中5种氯代烃均有检出,是河水长期渗漏积累的结果。凉水河流域内的野外试验结果表明,凉水河对地下水存在污染,污染组分主要是CODCr,NH3-N也有一定污染,其他无机污染组分如NO3-N,Cr6+,TP和Pb2+对地下水的影响较小,氯代烃对地下水也有一定影响。据推测,凉水河污染对地下水的影响范围大概在河两侧80 m范围内。     

小井距开发现河油田低渗油藏可行性研究

认为注采井网井距大,水驱控制程度差,采收率偏低是影响胜利油田现河低渗透油藏开发的关键,通过井间密度与水驱控制程度和采收率的关系等分析,提出了现河低渗透油藏开发的合理的井网密度。     

塔里木油田水碳酸盐平衡系数与有机酸的意义

根据统计学规律,对塔里木盆地油田水进行了研究,阐明了该盆地油田水的碳酸盐平衡系数(简称为R_C)与有机酸的基本特征。从油田水的无机组分与有机组分的统计分析中发现了油田水的碳酸盐平衡系数与有机酸存在明显的负相关性,进一步论证了碳酸盐平衡系数和有机酸与油气聚集及油气性质的关系。碳酸盐平衡系数越低及低碳有机酸的含量越高,它们与油藏,尤其是与 轻质油或气藏的关系越密切。从两者的关系中初步了解到有机酸的溶蚀作用对油气藏中储层次生孔隙的形成应有较重要的影响。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

基于SOI的双极场效应晶体管

在分析了双极型晶体管和场效应晶体管各自的特点和不足后，介绍了一种既具有双极型晶体管较大电流容量和功率输出，又具有场效应晶体管高输入阻抗的电子器件——双极MOS场效应晶体管(BJMOSFET)，同时指出体硅BJMOSFET的阳极扩散区与衬底之间存在较大的漏电流，可产生较大的寄生效应。提出了一种新型固体电子器件——基于SOI的BJMOSFET，分析了其工作原理j与体硅BJMOSFET比较，由于SOI技术完整的介质隔离避免了体硅器件中存在的大部分寄生效应，使基于SOI的BJMOSFET在体效应、热载流子效应、寄生电容、短沟道效应和闩锁效应等方面具有更优良的特性。     

End‐Capping as a Method for Improving Carrier Injection in Electrophosphorescent Light‐Emitting Diodes

The electronic properties, carrier injection, and transport into poly(9,9‐dioctylfluorene) (PFO), PFO end‐capped with hole‐transporting moieties (HTM), PFO–HTM, and PFO end‐capped with electron‐transporting moieties (ETM), PFO–ETM, were investigated. The data demonstrate that charge injection and transport can be tuned by end‐capping with HTM and ETM, without significantly altering the electronic properties of the conjugated backbone. End‐capping with ETM resulted in more closely balanced charge injection and transport. Single‐layer electrophosphorescent light‐emitting diodes (LEDs), fabricated from PFO, PFO–HTM and PFO–ETM as hosts and tris[2,5‐bis‐2′‐(9′,9′‐dihexylfluorene)pyridine‐κ²NC_3′]iridium(III ), Ir(HFP)₃ as the guest, emitted red light with brightnesses of 2040 cd m^–2, 1940 cd m^–2 and 2490 cd m^–2 at 290 mA cm^–2 (16 V) and with luminance efficiencies of 1.4 cd A^–1, 1.4 cd A^–1 and 1.8 cd A^–1 at 4.5 mA cm^–2 for PFO, PFO–HTM, and PFO–ETM, respectively.     

抽油机减速箱缺油保护系统的研制

抽油机减速箱损坏的主要原因之一是减速箱润滑油不足。目前,没有对抽油机减速箱内的油量进行实时监测,减速箱缺油后,抽油机不能立即停机,使减速箱在缺油状态下长期运转,造成齿轮、轴承损坏,甚至报废。为解决这一问题,研制了一种实时报警装置,当油量少于设定的最小值时,可以在现场发出报警信号,并对抽油机采取强制停机措施,起到保护减速箱的作用。     

Windows2000环境下实时控制系统的软件实现

文章介绍了在windows2000环境下通过编写WDM（Windows Driver Model）设备驱动程序实现实时数据采集和控制的一种方法。采用研华数据采集卡PCL818L产生中断信号．通过编写WDM驱动程序实现了在windows2000环境下转台的位置控制。并在实验中调试通过。实验结果表明：在采样频率为1KHz的情况下。控制系统很好实现了输出对输入的跟踪，证明了采用方法的正确性。该方法解决了windows2000环境下的实时性问题，为在windows环境下实时控制系统的实现提供了有益的尝试。