Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Influence of ethyl methacrylate content on the volume‐phase transition of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] microgels

A novel series of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] (p(NIPAM‐co‐EMA)) microgels was prepared by the surfactant‐free radical polymerization of N‐isopropylacrylamide (NIPAM) with ethyl methacrylate (EMA). The shape, size dispersity and volume‐phase transition behavior of the microgels were investigated by transmission electron microscopy (TEM), ultraviolet–visible (UV–Vis) spectroscopy, dynamic light scattering (DLS) and differential scanning calorimetry (DSC). The transmission electron micrographs and DLS results showed that microgels with narrow distributions were prepared. It was shown from UV–Vis, DLS and DSC measurements that the volume‐phase transition temperature (VPTT) of the p(NIPAM‐co‐EMA) microgels decreased with increasing incorporation of EMA, but the temperature‐sensitivity was impaired when more EMA was incorporated, causing the volume‐phase transition of the microgels to become more continuous. It is noteworthy that incorporation of moderate amounts of EMA could not only lower the VPTT but also enhance the temperature‐sensitivity of the microgels. The reason for this phenomenon could be attributed to changes in the complicated interactions between the various molecules. Copyright © 2004 Society of Chemical Industry     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

Catalytic reduction of N2O with CH4 and C3H6 over Ag–Rh/Al2O3 bimetallic catalyst in the presence of oxygen

A study of nitrous oxide (N₂O) reduction with methane (CH₄) and propene (C₃H₆) in the presence of oxygen (5%) over Ag/Al₂O₃, Rh/Al₂O₃ and Ag–Rh/Al₂O₃ catalysts, with Ag and Rh loadings of 5 wt% and 0.05 wt% respectively, has been performed. From the results, it was observed that the Ag–Rh bimetallic catalyst was the most active for both nitrous oxide removal (more than 95%) and hydrocarbon oxidation. This high activity seems to be connected with a synergistic effect between Ag and Rh. The findings from X‐ray diffraction and X‐ray photoelectron spectroscopy studies showed also, that there were no strong interactions (eg alloying) between Ag and Rh. Copyright © 2005 Society of Chemical Industry     

Equilibrium Moisture Characteristics of High Oleic Sunflower Seeds and Kernels

The equilibrium moisture content (EMC) characteristics of high oleic sunflower seeds and kernels between 10 and 55°C were determined by equilibrating the samples to known relative humidities (RH) above saturated salt solutions. EMC of the kernels was lower than that of seeds in the range of 11 to 96% ERH and at 25 and 40°C. Hysteresis effect was found for the EMC properties of seeds and kernels at 25°C. Four EMC-ERH models (modified Henderson, Chung-Pfost, Halsey, and Guggenheim-Anderson-de Boer) and their estimated parameters were evaluated for goodness of fit. GAB and Halsey equations showed the best fitting of experimental data although GAB equation adjusted for temperature described the EMC data the best. Components of the seed as oil content or hull/kernel ratio did not explain the slight differences in EMC found between the varieties.     

Copolymerization of bromophenylmaleimide with ethyl or butyl methacrylate

N‐p‐Bromophenylmaleimide (BrPMI) does not polymerize in solution by conventional free radical mechanism. However, it readily polymerized in bulk when mixed with a free radical initiator and heated in a microwave oven for 7–8 min. Copolymerization of ethyl methacrylate or butyl methacrylate with BrPMI was conducted in dioxane. The copolymers were characterized by IR and ¹H NMR spectroscopy and gel permeation chromatography. The monomer reactivity ratios were calculated by a non‐linear least‐square analysis. Thermal analysis indicated a great improvement in thermal stability of the copolymers compared with the methacrylate homopolymers. BrPMI was also polymerized in bulk in the DSC pan, which allowed the calculation of the activation energy of its polymerization. Copyright © 2003 Society of Chemical Industry     

Hydrogen absorption by Pd-coated ZrNi prepared by using Barrel-Sputtering System

To improve the durability of hydrogen storage materials against surface poisoning by impurity gases, effectiveness of Pd-coating layer prepared by using a Barrel-Sputtering System was examined for ZrNi powder. The effectiveness of Pd-coating was evaluated by activation temperature, at which Pd/ZrNi poisoned by air could be activated to absorb hydrogen. Characterization of Pd-coated ZrNi (denoted as Pd/ZrNi) by scanning electron microscopy, electron probe microanalysis and X-ray diffraction showed that a uniform Pd-coating layer was formed with the barrel-sputtering system. It was found that the poisoned Pd/ZrNi sample could be activated even at 423 K to absorb hydrogen at room temperature. This exhibits remarkable contrast to bare ZrNi, which could be only activated appreciably above 1073 K. It is concluded that the Pd-coating by barrel sputtering is quite effective to avoid the effect of surface poisoning of powdery hydrogen storage materials. However, the activation at excessively high temperature resulted in the loss of high activity to absorb hydrogen. It was concluded that this phenomenon was associated with reactions between Pd and ZrNi to form PdZr and other byproducts.     

Rapid analysis of polymer homologues and additives with SFE/SFC-MS coupling

A rapid and easy analysis method for polymers is presented. The method involves sample preparation by SFE, separation of the extracted compounds by SFC and simultaneous quantitative detection by FID, as well as identification of unknowns by MS. The applications illustrate how structural research work and routine polymer analysis can be done with this time saving method.     

A study of solid circulation rate in a circulating fluidized bed

An experimental investigation under cold condition was made to study the effects of some operating/design parameters and non-mechanical L valve configuration on the solid circulation rate in a 4.5 m tall, 0.15 m diameter circulating fluidized bed with riser flow rate varying from 1400 litres/min to 2000 litres/min and bed inventory from 15 kg to 25 kg of sand of average sizes 200 μm, 400 μm and 500 μm. Solid circulation rate was estimated by measuring velocity of sand particle travelling through a vertical Perspex tube section at the bottom of the return leg. It was found to be in the range of 2.8 to 12.3kg/m²s, 0.07 to 9.1kg/m²s and 0.12 to 2.23kg/m²s for sand sizes of 200 μm, 400 μm and 500 μm, respectively for a horizontal L valve. Two mathematical correlations have been developed from the experimental results to predict solid circulation rate as a function of riser flow rate, aeration flow rate, total bed inventory and particle size used.