水库水温分层对浮式取水口前流速分布的影响

由于目前缺乏对浮式取水口前流场变化规律的研究,以分析水库水温分层对取水口前各断面流速分布影响为目标,依据某水库水温资料,采用k-ε紊流模型对浮式取水口前流场进行三维数值模拟,针对水库水温均一和水温分层的两种情况,研究取水口前流速分布,分析水库水温分层对取水口前各断面流速分布的影响。研究结果表明,在浮式取水口附近,水温均一和水温分层的流速分布存在着差异,这种差距随着取水流量和淹没深度的增大而减小。研究成果可为浮式管型取水设施的应用和运行提供技术支持,为取水水温预测提供理论依据。     

水电站进水塔动水压力研究和探讨

基于理想流体,将进水塔简化成水中悬臂梁体系,推导了其受迫振动时的动力响应方程,给出了进水塔内外表面动水压力的解析表达式。与有限元法、水工抗震规范公式计算结果进行了对比,分析验证了该方法在进水塔结构上的适用性及准确性。结果表明:动水压力表达式与结构振型密切相关。该方法的动水压力曲线趋势与有限元方法相似,均在水面以下某深度处迅速变大及达到最大值后曲线值减小弯回,两者最终在塔体底部收于相近的值;最大值大于有限元法,其最大值处曲线折回明显,幅度较大。弹性模量和进水塔高度对动水压力的曲线形态和数值有重要影响。同时,输入激励荷载的频率对动水压力影响巨大,尤其频率与进水塔某阶频率相近时会导致动水压力的异常增大。该方法对分析进水塔动水压力具有参考价值。     

Estimating discharge in gravel‐bed river using non‐contact ground‐penetrating and surface‐velocity radars

Discharge measurement is a critical task for gravel‐bed channels. Under high‐flow conditions, the elevation of the riverbed changes significantly by intensive torrential flow. The stage–discharge relations commonly used for stream discharge estimation may no longer be adequate. The contact‐type velocity measuring is also subject to measurement errors and/or instrument failures by the high‐flow velocities, driftwood, stumps, and debris. This study developed a new real‐time method to estimate river discharge in gravel‐bed channels. A systematic measuring technology combining ground‐penetrating radar and surface‐velocity radar was employed. The rating curves representing the relations of water surface velocity to the channel cross‐sectional mean velocity and flow area were established. Stream discharge was then deduced from the resulting mean velocity and flow area. The proposed method was examined in a steep gravel‐bed reach of the Cho‐Shui River in central Taiwan. The estimated stream discharge during three flood events were compared to the prediction by using the stage–discharge relation and the index‐velocity method. The proposed method of this study is capable of computing reasonable values of discharge for an entire flood hydrograph, whereas the other two methods tend to produce large extrapolation errors. Moreover, when the computed discharge is used in 2D flood flow simulation, the proposed method demonstrates better performance than the commonly used stage–discharge and index‐velocity methods.     

PARTICLE FLOW PATTERNS IN THE RISER AND DOWNER OF CIRCULATING FLUIDIZED BED

This paper presents an experimental study on the flow patterns of FCC particles in a 140 mm ID Circulating Fluidized Bed with concurrent upflow and downflow gas-solid suspension. Based on the distribution of local particle velocity and particle concentration measured by a Fiber-Optical Probe Laser Doppler Velocimeter and a Fiber Optical Probe System respectively, the different flow patterns of local particls concentration, local particle velocity, local particle fluctuating velocity and sectionally average particle velocity in concurrent upflow and downflow gas-solid system have been investigated. It is found that the particle flow in the concurrent downflow is much more uniform radially than that in the concurrent upflow riser. The investigation of flow patterns in different flow systems is of significance to the development of a new gas-solid reactor.     

弯道岸坡上粗细泥沙统一起动流速公式

该文基于概率论与泥沙起动基本理论,考虑了起动概率、相对暴露度与细颗粒泥沙间黏结力和附加下压力对泥沙起动的影响,采用滑动起动模型,从理论上推导出了适用于弯道岸坡上粗、细泥沙颗粒起动的统一流速公式,完善了已有研究成果对泥沙起动概率考虑的不足。公式综合了弯道岸坡、顺直岸坡、正负坡及平坡等条件下粗细泥沙颗粒起动流速计算,可简化为各简单条件下泥沙起动流速公式。通过各简单条件下泥沙起动流速实测资料验证,该文公式与实测数据符合良好。     

全自动污泥脱水离心机的电气控制系统

介绍了采用恒差速恒力矩控制方案克服卧螺离心机处理城市污泥时容易产生的堵料问题,介绍了絮凝剂自动制备和添加装置。     

流化床二组分混合物的适宜分离气速

在等密度与非等密度二组分混合物分离体系中，考察操作气速对分离度的影响，提出物料的静床高对高效分离气速没有影响，而操作气速取其混合物最小流化速度的１．２倍左右时，二组分混合物产生高效分离，并且此操作气速随着二组分混合物分离状态的判定值（等密度混合物指Ｒｍｆ值，非等密度混合物主要指Ｒｐ值）的增加而拓宽。     

Noncertainty equivalent adaptive control of robot manipulators without velocity measurements

This paper presents a noncertainty equivalent adaptive motion control scheme for robot manipulators in the absence of link velocity measurements. A new output feedback adaptation algorithm, based on the attractive manifold design approach, is developed. A proportional-integral adaptation is selected for the adaptive parameter estimator to strengthen the passivity of the system. In order to relieve velocity measurements, an observer is designed to estimate the velocities. The controller guarantees semiglobal asymptotic motion tracking and velocity estimation, as well as L_∞ and L₂ bounded parameter estimation error. The effectiveness of the proposed controller is verified by simulations for a two-link robot manipulator and a four-bar linkage. The results are further compared with the earlier certainty-equivalent adaptive partial and full state feedback controller to highlight potential closed-loop performance improvements.     

Pickup (critical) velocity of particles

This work presents experimental results on pickup velocity (critical velocity) measurements for a variety of particulate solids. The present experiments together with previously published experiments of a number of researchers encompass about 100 measurements of 24 materials for a wide range of particle sizes, shapes and densities. Based on the experimental results, three zones are defined by establishing simple relationships between the Reynolds and Archimedes numbers. The empirical relationships were further modified by taking into account the pipe diameter and particle shape (sphericity). The three-zone model was shown to reasonably correlate to Geldart's classification groups.     

Microstructure and thermal cycling behavior of thermal barrier coating on near-α titanium alloy

Two kinds of thermal barrier coatings (TBCs), consisting of NiCoCrAlY bond coats (BCs) deposited by electron beam-physical vapor deposition (EB-PVD) and high velocity oxy-fuel (HVOF) thermal spraying, respectively, and top 8 wt%Y₂O₃–ZrO₂ (8YSZ) ceramic layers deposited by EB-PVD were prepared on near-α titanium alloys. The field emission scanning electronic microscopy and microhardness indentation are used to study the microstructure and microhardness. Different failure features including cracking patterns and the delamination degree of these two TBCs are discussed according to the thermal cycling tests in the atmosphere. It is found that the morphology of the two BCs deposited by different methods (EB-PVD and HVOF) determines the microstructure and microhardness of their corresponding top 8YSZ layers. The BC prepared by EB-PVD is dense and homogeneous, which leads to a dense and hard 8YSZ with clustered slim columnar grains. The BC prepared by HVOF, however, is porous and inhomogeneous in microstructure and, as a result, the top ceramic layer is loose with low microhardness and clustered coarse columnar grains.