Heat and Mass Transfer Analogy Studies of Binary Liquid Mixture in Comparison with Eteanol-n-Heptane Evaporating to Air

An expenmental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 mls. An illustrative example of the use of the theory for industrial ventilation is presented.     

GaAs FET辐射退化研究

低噪声ＧａＡｓ ＦＥＴ和功率ＧａＡｓ ＦＥＴ经中子辐射都未发生致命性的通或断失效，直流偏置伏态下，其失效模式仅仅表现为源漏饱和电流ＩＤＳＳ的退化降低，据此提出了ＩＤＳＳ退化失效与快中子注量φｎ之间的解析关键式ｌｎｙ＝ａ＋ｂｌｎφ。     

Engineering Model of a Nonisobaric Heavily Laden Gas‐Particle Jet

An axisymmetrical model of a rapid nonisobaric heavily laden gas‐particle jet is developed. The model is based on the general functions for both axial and radial pressure distributions, which were discovered by a numerical study of rapid gas‐particle jets by the CFD code. The model equations were solved analytically. The results obtained by the model developed are in good agreement with those computed by the CFD code for a wide range of flow parameters.     

ANALYSIS OF EXPERIMENTAL AND NUMERICAL RESULTS OF A TURBULENT SWIRLING FLOW IN A TUBE

In many applications swirling flow is used to enhance heat and mass transfer. One of the problems of modelling a turbulent swirling flow is the choice of the turbulent closure model which is acceptable for engineering purposes. To evaluate which model performs best, numerical results are compared with experimental data. Local velocity measurements are carried out on a swirling flow in a circular tube. The measurement method is hot-wire anemometry combined with visualization techniques. The numerical analysis is carried out using the k-ε model and the Algebraic Stress Model. In the experiment a symmetrical swirl was observed, Comparing the experimental data with the numerical results shows that the Algebraic Stress Model represents the experimental data quite well, whereas the k-ε model fails.     

RADIOACTIVE OR NATURAL TRACER。TECHNIQUES FOR LEAK DETERMINING OF DAM ABUTMENT

Infiltration and localization of preferential infiltration zones at the dam abutment are measured using radioactive tracer tests of flow in boreholes,meanwhile interconnection between boreholes and the energing water points is analysed.The theory and practice of radioactive tracer synthetic detective method are described to give methods and calculation formulae used under the condition of stable flow in single well to measure permeability coefficient and hydrostatic heads.Major single hole techniques including measurement for seepage line,velocity,rate of seepage flow and relationship of recharge of groundwater in aquifers are introduced briefly.The possibilities offered by natureal tracers are analysed,uincluding electric-conduct,pH-value and temperature of water as well as stable isotopes(D,^18O) and tritium.Furthermore,the sensibilities of this theory and methods were confirmed by detecting seepage flow field of Xinanjiang Dam.     

凝固过程中的颗粒推斥

颗粒推斥是材料在固液相变过程中的基础问题之一，界面自由能的传统理论难以解释在金属基复合材料制备过程中的颗粒推斥现象，作者提出了固液界面前沿的流体流动是颗粒推斥的主要原因之一，并给出颗粒滚动及颗粒速度两种作用机制，推导出颗粒推斥条件判据，并以实验验证流体流动的作用机制及颗粒推斥理论判据。     

INVESTIGATION OF THE USE OF LASER-DOPPLER VELOCIMETRY IN TWO-PHASE BUBBLY FLOWS

Understanding the dynamic phenomena of viability loss of shear sensitive cells and bubble breakage and coalescence within airlift reactors requires knowledge of local, liquid-phase hydrodynamics. The laser-Doppler velocimeter (LDV) is a non-invasive instrument which may be used to obtain this information. Experimental procedures and software were developed to detect and measure Doppler bursts in two-phase flow in a split-cylinder airlift reactor. Off-line analysis of the data indicated a detection rate approximately one order of magnitude greater than that observed using an available commercial frequency tracker. Approximately 400 to 500 observations are needed for the ensemble mean to characterize the local mean velocity to within ±5% for a superficial gas velocity of 10.4 cm/s, the highest superficial gas velocity used in these studies. The limitations, prospects, and signal-processing options for LDV in this application are also discussed     

Development of the meshless finite volume particle method with exact and efficient calculation of interparticle area

The Finite Volume Particle Method (FVPM) is a meshless method based on a definition of interparticle area which is closely analogous to cell face area in the classical finite volume method. In previous work, the interparticle area has been computed by numerical integration, which is a source of error and is extremely expensive. We show that if the particle weight or kernel function is defined as a discontinuous top-hat function, the particle interaction vectors may be evaluated exactly and efficiently. The new formulation reduces overall computational time by a factor between 6.4 and 8.2. In numerical experiments on a viscous flow with an analytical solution, the method converges under all conditions. Significantly, in contrast with standard FVPM and SPH, error depends on particle size but not on particle overlap (as long as the computational domain is completely covered by particles). The new method is shown to be superior to standard FVPM for shock tube flow and inviscid steady transonic flow. In benchmarking on a viscous multiphase flow application, FVPM with exact interparticle area is shown to be competitive with a mesh-based volume-of-fluid solver in terms of computational time required to resolve the structure of an interface.     

3-D hydrodynamics generated in a stirred vessel by a multiple-propeller system

The aim of this study is to optimize the position and the number of propellers in a non-standard tall vessel. Laser sheet flow visualization experiments were carried out for selected geometrical arrangements which produced stable flow patterns and good transport between the propellers. Four double-propeller arrangements corresponding to frequent industrial cases and a three-propeller system have been chosen. Comparison of LDA measurements in the r-z plane, dimensionless global parameters N_Qp, Nt_m, N_p, E_p and spatial distribution of local energy dissipation rate ? shows that a three-propeller system is the most efficient.