Correlation of reactivity with chemical structure: Thermal hydrogenation of gas oils

The relationship between chemical structure and reactivity for thermal hydroprocessing was studied for five gas oils derived from Alberta bitumens. Chemical structure was characterized by combining data from ¹ H and ¹³ C nuclear magnetic resonance spectroscopy, class fractionation, and elemental analysis to calculate structural parameters. Thermal hydrotreating was performed in a continuous-flow stirred reactor at 420 and 440°C, 13.9 MPa hydrogen pressure, and 1.5 h¹ LHSV. Conversion of the 343–525°C boiling fraction of the gas oils was correlated with the concentration of naphthenic methylene groups in the feed. Formation of methane and ethane was dependent on the degree of condensation of the aromatic rings in the feed oils. Thermal desulfurization was highly correlated with the amount of saturates in the feed, and the aromaticity of the resin fraction. Hydrogen consumption increased with the aromaticity of the gas oil…     

过磷酸钙含氟尾气处理的新方法

对动态泡沫床处理过磷酸钙含氟尾气的有关技术及费用作了说明 ,指出该方法费用高 ;提出一种新方法 ,该方法不加任何化学助剂 ,采用水作吸收剂 ,只需改变动态泡沫床一些设计参数和选用一种特殊的喷头 (喷头周围设计 1个圆锥形死角区 ,使含氟气体不可能进入该区 )避免了硅胶堵塞。该方法已在湖南浦市化工总厂运行 1年多未发现堵塞 ,同时该法投资少、能耗低、排放尾气达标     

浅谈脱硫液中PDS质量浓度测定方法

提出了在以PDS催化剂作为单一的脱硫催化剂时,脱硫循环液中贫富液的PDS质量浓度的测定方法,可有效地指导在脱硫工序投加PDS的操作及生产运行,为确保出脱硫工序煤气中H2S含量稳定控制在20mg/L以内奠定了基础。     

我国烧碱生产技术概况

介绍了我国氯碱行业近几年来的发展情况：分析了我国烧碱生产的工艺技术现状。指出了为缩短与世界先进国家的差距需要加快开发关键设备和高性能的离子膜，加强管理。     

Gas hold-up in non-newtonian solutions in a bubble column with internals

Bubble characteristics and gas hold-up were studied in a two phase (air-aqueous CMC solution) bubble column provided with helical coils and straight tubes as internals. The effects of superficial gas velocity, rheological properties, and volume fraction covered by the internals, on gas hold-up were studied. Hold-up values determined directly and by simultaneous pressure drop measurements matched well. Enhancement of gas hold-up values up to 55 per cent was achieved in systems using internals. The gas hold-up results were also compared with the values obtained from correlations reported in the literature.     

溴虫腈土壤和甘蓝微量残留量的气相色谱法测定

采用气相色谱法定量分析溴虫腈土壤和甘蓝微量残留量。样品经丙酮提取 ,液 液分配及氧化铝柱层析法净化后 ,以GC ECD测定 ,DB 170 1毛细管柱 ,氮气为载气 ,柱温 2 6 0℃ ,汽化室温度 2 5 0℃ ,检测器温度 2 80℃ ,外标法定量。该方法快速、准确 ,在 0 0 1～ 2 0 0mg/L范围内线性相关系数r2 =0 9999,平均回收率 90 0 %～ 10 3 6 7% ,变异系数 4 4 8%～ 5 89% ,最小检测量 2× 10 12 g ,最低检出浓度 3 3× 10 4mg/kg。     

液氨贮存设计分析

氨是生产含氮肥料及尿素的基本原料，为确保原料供应，必须设置其贮存设施。介绍了常温中压、降温低压和低温常压三种不同的液氨贮存工艺及其特点，并以某大型氨站设计为例，分析了液氨贮存工艺流程、主要设备、材料的选型和工艺参数的确定。     

Kinetic modelling of the catalytic conversion of synthesis gas

A kinetic study for the one-step conversion of synthesis gas to gasoline on a ZnO–Cr₂O₃–ZSM-5 catalyst is described. On this catalyst, three reactions are involved in the overall transformation of synthesis gas: the methanol synthesis, the conversion of methanol to hydrocarbons and the water–gas shift reaction. Under the operating conditions selected for the study, it was found that the water–gas shift was at equilibrium and the methanol was completely converted to hydrocarbons. Consequently, it was postulated that the kinetics of the limiting reaction step, the methanol synthesis on the ZnO–Cr₂O₃ component, was the one that controls the overall reaction rate. Three kinetic model equations describing the rate of synthesis gas conversion on the bifunctional catalyst, were considered to fit the data of the experimental runs performed in a Berty well-mixed reactor. Those equations were derived under very special conditions where the methanol decomposition term could be neglected. It was also observed that in the kinetic equations a term involving the fugacity of CO₂ was required to predict the rate properly. The catalyst deactivation was also taken into account in the analysis.     

气体控制参数对气体辅助成型产品翘曲的影响

从气体辅助注射成型工艺的角度探讨了气体的延迟时间和第一段压力这两个关键的参数对槽的影响进而对产品翘曲变形的影响，结果表明：虽然通过使用气体辅助注射成型技术能改善产品变形，但并不能完全消除变形；造成产品变形的原因和机理十分复杂，只有进行从设计到工艺的全方位考察才能有效的控制变形，气体手指效应也是造成产品变形的一个重要因素，工艺上可以通过调整延迟时间和气体压力来减小产品的变形量。