Investigations of water inrushes from aquifers under coal seams

In many coal mines, limestone-confined aquifers underlie coal seams. During coal extraction from these mines, water inrushes occur frequently with disastrous consequences. This paper introduces the hydrogeological conditions of the coal mines and the potential water inrush disasters from aquifers under coal seams. It then presents the water inrush mechanism. The main factors which control water inrushes include strata pressure, mining size, geologic structures and the water pressure in the underlying aquifer. Analysis shows that reduction of confinement due to mining is the major cause of the water-conducting failure in the floor strata. The depth of the failure zone is strongly dependent on the mining width. This paper also presents field observation results of the water-conducting failure in the floor strata, and applies the finite element method coupled with stress-dependent permeability to analyze hydraulic conductivity enhancement due to coal extraction. Finally, theoretical and empirical methods to predict water inrushes are given, and technical measures for improving mine design and safety for coal extraction over aquifers are presented. These measures include fault and fracture grouting and mining method modification such as changing long-wall to short-wall mining.     

水喷雾灭火系统在电信枢纽工程燃气锅炉房的应用

分析了燃气锅炉的火灾危险性和水喷雾用于燃气锅炉消防的灭火机理,提出了水喷雾灭火系统的设计参数的选择、系统的控制方法以及在设计中可能涉及到的问题和注意事项,并结合工程实例进行了探讨。     

Ice-slurry production using direct contact heat transfer

An ice slurry generation system was developed using direct contact heat transfer between water and the coolant, Fluroinert FC-84. The location of the coolant nozzle is an important design consideration to avoid clogging due to freezing of water. An ice fraction of up to about 40 percent was obtained with the nozzle located at the bottom of the ice slurry tank and the jet directed upwards into the water. Two simplified model were developed to extract the heat transfer coefficient between the coolant drops and the water. The first model requires as input the average drop diameter and the residence time while the second model uses the measured drop diameter distribution. The estimated heat transfer coefficients are much smaller than those computed using single-sphere correlations.     

Hydrothermal Modeling Studies of Cooling Tower Alternatives

The Environmental Effects Committee of the ASCE Energy Engineering Division has been developing a report on “Energy Production and Reservoir Water Quality” for publication. The report covers the regulatory framework that dictates much of the procedures for studies related to this topic, the fundamental reservoir hydrodynamics and water quality modeling used in preparing studies, the kinds of studies that can be prepared at different levels of analysis, and a series of applications that illustrate the problems encountered and applications of the various techniques. This study of hydrothermal modeling as applied to examining cooling tower alternatives for an existing steam electric station on a moderately large reservoir is included in this report and is presented here as an illustration of the types of studies included. This particular study subtended the usual steam electric plant cooling water discharge studies that relate to specific regulatory thermal plume size standards, and had to be designed around developing plant and cooling tower operations that would meet specific fisheries requirements for a zone of passage and refuge for fishes throughout the receiving embayment. After being used in developing cooling tower and plant operating details for the designers to work with, it was required that the hydrothermal modeling results be verified under actual tower operating conditions. In addition, it was required that the impact of the combined operations on dissolved oxygen be examined in detail. This paper covers the background to setting up the study, the kinds of statistical comparisons used to verify the hydrothermal studies, and similar studies for the analysis of dissolved oxygen distributions.     

In Situ Performance Testing of Deteriorating Water Tanks for Durability Assessment

Reports of failure of existing concrete structures due to a lack of durability, rather than a deficiency in structural strength, has made concrete technologists, engineers, and researchers focus research on the parameters influencing durability performance with respect to time. Systematic performance monitoring, with respect to chosen durability parameters of existing concrete structures, will decide the direction of future research in this area. Inferences based on laboratory simulations and testing need to be confirmed by in situ field measurements and studies. In situ condition rating and performance monitoring surveys have been conducted by many researchers, scientists, and professional associations, and reported in literature. Inferences of few such studies are summarized and discussed. Deterioration of concrete structures constructed in recent times is observed at relatively faster rates, and has been mainly attributed to cracking. Cracking is associated with the use of faster-hydrating portland cements with increased fineness and the tricalcium silicate (C3S) content to support the high speed of modern construction. In the present research, a case study of deteriorated water tank structures situated in the semitropical region of India is presented. Some selected parameters—such as concrete cover, carbonation depth, chloride concentration, compressive strength, etc. which influence long term durability of structures—have been measured.     

定向爆破拆除框架式水塔

高 2 7m的水塔建于 193 4年 ,其顶部水罐由 12根钢筋混凝土柱支撑。在倒向侧 7根立柱上形成不同高度的爆破切口 ,背向侧倾倒中心线上的一根立柱上形成小爆破切口 ,其余 4根立柱底部打贯通孔 ,使水塔准确定向倾倒。文中讨论了立柱切口高度的计算 ,爆破参数的确定 ,并介绍了所采用的安全措施。     

预测水驱油田开发动态的一种方法

水驱曲线法和数学模型法都是油藏工程中的重要方法，前者主要用于在一定的经济含水条件下预测水驱油田的可采储量和采收率，后者主要用于预测不同类型油田的产量、累积产量和一定经济极限产量下的可采储量。然而，前者与时间序列无关，后者与含水率序列无关，都有局限性。提出丙型水驱曲线公式与ＨＣＺ数学模型公式联解预测法，不但可以预测水驱油田产量、累积产量、含水率随时间的变化，还可预测可采储量、可动油储量和水驱波及体积系数的变化。图３表１参１２（陈志宏摘）     

Inhibiting and deactivating effects of water on the selective catalytic reduction of nitric oxide with ammonia over MnOx/Al2O3

The effect of water on the selective catalytic reduction (SCR) of nitric oxide with ammonia over alumina supported with 2–15 wt.-% manganese oxide was investigated in the temperature range 385–600 K, with the emphasis on the low side of this temperature window. Studies on the effect of 1–5 vol.-% water vapour on the SCR reaction rate and selectivity were combined with TPD experiments to reveal the influence of water on the adsorption of the single SCR reactants. It turned out that the activity decrease due to water addition can be divided into a reversible inhibition and an irreversible deactivation. Inhibition is caused by molecular adsorption of water. TPD studies showed that water can adsorb competitively with both ammonia and nitric oxide. Additional kinetic experiments revealed that adsorbed ammonia is present in excess on the catalyst surface, even in the presence of water. Reduced nitric oxide adsorption is responsible for the observed reversible decrease in the reaction rate; the fractional reaction order changes from 0.79 in the absence of water to 1.07 in its presence. Deactivation is probably due to the dissociative adsorption of water, resulting in the formation of additional surface hydroxyls. As the amount of surface hydroxyls formed is limited to a saturation level, the deactivating effect on the catalyst is limited too. The additional hydroxyls condense and desorb in the temperature range 525–775 K, resulting in a lower degree of deactivation at higher temperature. A high temperature treatment at 775 K results in a complete regeneration. The amount of surface hydroxyls formed per unit surface area decreases at increasing MnO_x-loading. The selectivity to the production of nitrogen is enhanced significantly by the presence of gas phase water.     

Catalytic decomposition of HCFC22 (CHClF2)

The catalytic decomposition of CHClF₂ was studied over various acidic metal oxides in a fixed-bed reactor. The Cr₂O₃ZrO₂ exhibited the highest activity. The presence of water vapor in the reaction system suppresses the transformation of oxides to fluorides, progresses the formation of CO₂, and it improves the catalysts life.     

Catalytic oxidation of sulphide ions to elementary sulphur in aqueous solutions over transition metal oxides

The catalytic activity of a wide range of transition metal oxides in oxidation of sulphide ions by air in aqueous medium was studied. Some specific features of the reaction mechanism on some of the studied oxides were considered. The transition metal oxides are promising catalysts for practical application. Some of these oxides will allow the preparation of catalysts possessing activity comparable to that of the cobalt phthalocyanine based catalysts, popular in industrial practice.