板式换热器热端跑冷问题的分析及处理

１００００ｍ３／ｈ制氧机板式换热器损坏修复后，热端跑冷严重，氧气取出量不足，制氧机工况恶化，通过分析找出了原因是因某单元氧通道堵塞，并采取了处理措施。     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

烧结机双层插板式卸灰阀的研制

烧结机双层卸灰阀由蘑菇头式改为电液推杆插板式，有效地解决了系统卸料及漏风问题，实现了控制自动化，提高了设备作业率，改善了岗位环境。     

FEM model of the ohmic resistance of IP-SOFCs

In the present work, the ohmic resistance of an integrated planar-SOFC (IP-SOFC) has been evaluated by developing a model whose equations have been solved numerically through an FEM method. The model allows to estimate the distribution of voltage and current density in the cell. A comparison between simulated and experimental data of area specific resistance is reported, which shows satisfactory agreement. The mathematical model has also been used to carry out some parametric studies for optimisation purposes. Indeed, a reduction in cell pitch length and an increase in electrode thickness are predicted to lead to a reduction in ohmic losses in IP-SOFCs.     

冷却水污垢及其对冷却器换热的影响

分析了冷却器的结垢机理 ,提出了冷却器污垢层、污垢热阻随运行时间的规律 ,以及污垢热阻与换热系数、换热面积的关系式 ,并通过算例阐述了污垢热阻对冷却器的影响程度 ,进而定性地分析了污垢热阻对空分装置的影响。     

空气压缩机无油润滑在山脚树矿的应用

山脚树矿有5台1966年上海生产的4L—20/8空气压缩机,运行很不经济,利用聚四氟乙烯合成材料制成活塞环,全部实现无油润滑运转,取得了良好的经济效益。     

一种T形高压输电线路故障测距新方法

对T形线路的故障测距，现有方法都是先判断故障支路，再将3端线路等效成2端线路进行测距。但在 T节点附近短路，尤其是经高阻短路时，现有的测距方法由于无法正确判别故障支路而存在一定范围的测距死区。针对上述缺陷，分别假设故障发生在某一支路，由假定正常的2段支路端的电压、电流推算求得 T节点电压和注入假定故障支路的电流，从而分别求得3个故障距离。经证明，求得的3个故障距离有且仅有1个在0和对应支路总长度之间，该距离就是真实的故障距离，故障发生在对应支路上。该方法无需事先判别故障支路即可测距，在 T节点附近经高阻故障时无测距死区。其测距精度理论上不受过渡电阻和故障类型影响，无需故障前数据，且对滤波无高要求。EMTP仿真结果表明该方法正确、有效，测距精度高。     

"摩圣"技术在空气压缩机上的应用

介绍了4L-20/8型空气压缩机采用"摩圣"技术后的运行情况。"摩圣"技术在设备正常运行条件下能成功修复摩擦副的磨损,使之恢复原设计的尺寸和要求,因而提高了生产效率,取得了显著的经济效益。