能量"三环节"理论在原油蒸馏装置扩能改造中的应用

中国石化扬子石化股份有限公司炼油厂在第一套常减压蒸馏装置扩能改造中，使用了多项节能技术以实现能量的优化利用。本文以标定数据为基础，运用能量“三环节”理论对该装置的用能状况进行了计算和分析，从能量利用角度对装置的扩能改造效果进行了评价，并为装置的进一步优化能量利用提出了相应措施。     

异形柱柱头混凝土连续托梁分次置换技术

通过某工程异形柱头混凝土置换实例,介绍了连续托梁分次置换技术的设计计算、施工方法和技术措施等。     

活塞式压缩机吸排气管道的振动与控制

阐述了活塞式压缩机吸、排气管道强烈振动的危害，分析了产生共振的原因，介绍了现场消减管道振动的有效措施。     

丙烯腈急冷塔喷淋系统流道分析与优化

对国内现有丙烯腈装置急冷塔循环液喷淋器的分流流道进行了研究。对喷头堵塞情况作了理论分析，并运用计算机编程模拟计算出喷淋器中各喷头的流体分布情况。在此基础上提出了分流流道的优化方案，从而改善了急冷塔内的操作状况，减少了丙烯腈在急冷塔内的损失。     

隔壁精馏塔分离芳烃混合物的模拟研究

采用隔壁精馏塔分离苯-甲苯-对二甲苯物系,用Aspen Plus软件模拟了隔壁精馏塔内温度分布及液相组成分布,考察了汽相和液相分配比对产品纯度的影响。对隔壁精馏塔模拟得到的优化操作条件为:隔壁精馏塔的理论板数为30块,侧线采出在第14块理论板,进料段为15块理论板,在进料段的第7块理论板进料,进料组成n(苯)∶n(甲苯)∶n(对二甲苯)为1∶3∶1,回流比为8.8,液相分配比为2.96,汽相分配比为0.83。在此条件下,各组分的摩尔分数大于98.5%,与实验结果基本吻合。当进料组成n(苯)∶n(甲苯)∶n(对二甲苯)为1∶3∶1时,采用隔壁精馏塔可比常规两塔流程节能27.18%。     

异形柱框架结构设计方法分析与参数控制

近年来,异形柱框架结构(框轻结构体系),因其能较好地满足建筑使用上和结构性能上的要求,而逐步得到了推广应用,并被列为建设部首批住宅建设新技术推荐目录。但异形柱框架结构设计目前还没有可依据使用的国家标准和行业标准。本文根据对江苏省地方标准《钢筋混凝土异形柱框架结构技术规程》(DB32/512-2002)的理解,结合笔者设计实践经验,提出个人看法,供同行参考。     

Residue curve maps for reactive distillation systems with liquid-phase splitting

A model has been developed to study the effects of chemical kinetics on the residue curve maps (RCM) for reactive distillation systems with liquid phase splitting. In the model, chemical reaction can occur in both or only one of the two liquid phases. The heating policy V/V₀=H/H₀ is applied so that the kinetic effect can be described by a single parameter, the Damköhler number Da. The effects of reaction kinetics on pseudohomogeneous and heterogeneous mixtures have been compared. The properties of their RCMs are the same outside, but are fully different inside the liquid-liquid (L-L) region if they have different chemical equilibrium curves. Inside the L-L region, the chemical equilibrium curve coincides to a unique reactive liquid-liquid tie line in case that the pseudohomogeneous chemical equilibrium curve intersects with the L-L envelope. When the reaction occurs in only one of the two liquid phases, the residue curves inside the L-L region are strongly affected by the L-L envelope, especially at high Da. In the present paper, first an illustrative arbitrary reaction system, and then the reaction of cyclohexene with water to cyclohexanol are analysed with respect to their RCMs.     

�͹�����Һ����񶯷���

油管柱作为油气生产中的重要工具，它的使用寿命一直是工程技术人员关注的焦点。文章从动力学中固液耦合振动的角度出发，研究了油管柱内流体不稳定流动引起的油管柱振动问题。考虑液动压力对油管柱纵向振动的影响，建立了油管柱纵向振动微分方程，并给出了这种情况下油管柱纵向振动的频率方程。通过大天池构造上一口高压气井的实例计算分析，指出井内流体不稳定流动时，油管柱会产生相当高的附加动载。这个动载是造成油管柱在生产过程中发生疲劳破坏的主要原因之一，在今后的油管柱设计中应考虑这一动载的影响     

常减压蒸饱装置几起典型硫腐蚀事例分析

随着高（含）硫原油加工量的增加,硫腐蚀事故也时有发生。通过对常减压装置硫腐蚀事例进行分析,指出合理的混炼比,加强“一脱三注”管理,材料升级和实施腐蚀监测是防止腐蚀事故发生的有效措施。     

Design and control of an olefin metathesis reactive distillation column

This paper considers the design and control of a reactive distillation column in which one reactant is consumed and two products are formed (A?B+C). The volatilities are α_B>α_A>α_C, i.e. the reactant is intermediate boiling between the two products. The metathesis of 2-pentene is considered as the demonstrative example. The column has a single feed of the intermediate boiling reactant. The distillate contains mostly light component and the bottoms mostly heavy.Three designs are considered: the base case (low-conversion/low-pressure), a low-conversion/high-pressure case and a high-conversion/high-pressure case. The base design is obtained from the literature, and the other two steady-state designs are optimized with respect to the total annual cost. All the designs are found to be openloop stable. Five control structures are studied for the base design. Then the best two structures are applied to the remaining two designs. This category of reactive distillation exhibits less challenging problems than other categories since it uses a single feed, which eliminates the need for the control structure to perfectly balance two fresh feeds.Simulation results demonstrate that effective dynamic control is provided by a control structure that uses two temperatures to maintain the purities of both product streams. No internal composition measurement is required. This structure is found to be robust and stable and rejects loads and tracks setpoints very well.