Symbol error probability of an OFDM receiver with pulse blanking based on the peak value threshold

Pulse blanking based on the peak value threshold is a widely used method to eliminate impulsive interference in the orthogonal frequency division multiplexing (OFDM) receiver. To assess the impact of pulse blanking on the link transmission reliability of the OFDM receiver, the analytical expression for the signal-to-noise ratio (SNR) of the OFDM receiver with pulse blanking based on the peak value threshold is derived in the frequency selective fading channel. According to this analysis, the calculation method for symbol error probability is given in this paper. Computer simulation indicates that theory accords with simulation and validates the accuracy of theoretical analysis.     

Effects of parameters on rotational fine blanking of helical gear简

The application of fine blanking to the manufacturing of helical gears directly from a strip has been restricted due to the traditional linear cutting stroke of the punch and die. In this work, rotational fine blanking which combined the linear and rotational motion of punch and counterpunch was applied for the forming of helical gears. A three-dimensional （3D） rigid-plastic finite element model was developed on the DEFORM-3D platform. By finite element simulation and analysis, the influences of key parameters on the punch load and cut surface were investigated. It is shown that： 1） with increasing the counterforce or helical angle, the punch load and the depth of die roll increase; 2） with increasing blank holder force, the punch load increases while the depth of die roll decreases; 3） V-ring indenter facilitates an improvement in the quality. The results of this research reveal the deformation mechanism of rotational fine blanking of helical gears, and provide valuable guidelines for further experimental studies.     

Method for calculating dynamic yield stress of fresh cement pastes using a coaxial cylinder system

The calculation of the rheological parameters of fresh cement pastes plays a key role in understanding the rheology of cement-based mixes. Because cement paste is not a simple Bingham fluid, a suitable nonlinear model must be found for characterizing its flow. A test system in which the rotational speed or shear rate can be changed in multiple steps is regarded as a suitable rheological test protocol because the paste reaches a steady state. Furthermore, theoretical derivations show that the solution of the Couette inverse problem corresponding to the modified Bingham model and the Herschel–Bulkley (H-B) model is complex. However, a comparative analysis revealed that the yield stress of fresh paste could easily be obtained through a calculation process based on a Parabolic model. This study presents the complete calculation procedure for this model. The influence of the plug flow is considered, and test points with low minimum shear stress (τ_min) are excluded. Finally, the accuracy of the proposed method is verified through comparisons with the results obtained using mini-cone slump tests. These results show that the dynamic yield stress calculated using the expression of the Couette inverse problem based on the Parabolic model in consideration of the plug flow is very close to the yield stress obtained using the mini-cone slump flow test. This proves that the proposed method could precisely characterize the dynamic yield stress of cement pastes.     

聚氨酯橡胶冲裁模具的设计探讨

在冲裁薄料时，通常要用的是无间隙的冲模。以聚氨酯橡胶代替通常钢模中的凹模或凸模是比较有效的方法之一。在了解聚氨酯橡胶冲裁的过程和聚氨酯橡胶冲裁的工艺性的基础上，必须掌握聚氨酯橡胶；中裁模具主要零件的设计要领。     

微小型静电泵的锥型塞阀门设计

锥形塞结构的阀门作为静电泵的出、入液体的调节机构,出、入阀门的流量是相同的,但在阀门开启状态下出、入阀门的压力差不同,这取决于出、入管道内压力。取较小者进行讨论作为结果,保证大者畅通无阻并且实现了锥塞加工尺寸一致性。根据流体力学关于流量和压力差关系,先采用流量系数0. 3计算出环隙流面积和在环隙中的流速。设定锥塞外环隙大小后,由这些数据能算出雷诺系数,再推测与其相关的流量系数为0. 26～0. 7,与计算所选用的0. 3接近或更大,说明相同的Δp条件下,能保证规定的流量及其他相关计算结果。选择合适锥塞或锥形管的锥半角,可保证锥塞外环隙流通面积恒定。     

新型穿孔顶头的研究

介绍了穿孔顶头的工作条件和主要失效形式，以及新型穿孔顶头的设计。确定了顶头的生产工艺。使用结果表明，新型穿孔顶头在穿孔中能保持良好的流线型外形，产生光滑的再生氧化层，防止塌鼻失效，提高了使用寿命。     

Ф100mm单槽自动轧管机组的技术改造与实践

介绍了应用先进的工艺和设备对Ф100mm单槽自动轧管机组生产线以及局部生产设备进行的技术改造。改造后的机组扩大了产品规格，增加了品种，提高丁产品质量，特别是提高了产品的几何尺寸精度，使企业获得了生机。其经验亦可作为其他Ф100mm自动轧管机组改造借鉴。     

穿孔顶头使用寿命浅析

分析了顶头的各种失效形式及产生的原因,提出了提高顶头使用寿命的措施。即应根据顶头的具体工作条件,制定合理的热处理工艺;采用复合处理工艺,解决好顶头单纯氧化处理热强性不高的问题等。     

端盖板高速连续级进模设计

根据制件的形状和生产要求，对RF-300C系列微电机端盖板的结构及工艺性进行了分析。介绍了一副轴承室深度和内径可调的端盖板高速连续级进模的排样设计和模具结构，分析了它的结构以及主要零部件的设计特点；叙述了压凸包、整形、打麻点、落料复位等模具结构在高速连续级进模中的设计方法。实践证明该模具结构可靠，运行状态稳定，制件质量符合技术要求。     

冲裁小凸模强度计算的新探讨

对无凸模导向和保护套的模具结构进行分析，提出冲裁小凸模强度核算应考虑的问题。