丙烯酸酯与甲基丙烯酸酯的共聚及性能研究

采用悬浮聚合法，以丙烯酸－２－乙基－己酯与甲基丙烯酸十二酯为单体，合成了共聚型高吸油性树脂。研究了共聚单体的配比、交联剂用量、引发剂用量诸因素对高吸油性树脂的性能影响。制得的树脂可以吸其自身质量的１１．８倍的煤油、１４．７倍的苯、６．５倍的泵油。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Bulk growth of Hg0.8Cd0.2Te single crystals by a combined CVT-seeding technique

The growth of high quality Hg_0.8Cd_0.2Te bulk single crystals by CVT, combined with an in-situ seeding technique, is reported here for the first time. For this purpose, a temperature difference of 590° → 540° C with a gradient of 40°-50° C/cm at the solid-vapor interface, and about 0.1 atm of HgI₂ as a transport agent, were employed. The bulk crystals have the expected stoichiometry and compositional homogeneity. Etch pit densities of 10⁴-10⁵ cm⁻² on the (111) face and hitherto unreported etch pits on the (100) face were observed in this work. Possible origins of the sub-grain structure are discussed.     

Cationic ring-opening polymerization of hexamethylcyclodisilazane: General aspects and tentative mechanisms

The ring-opening polymerization of hexamethylcyclodisilazane (D_2NMe), initiated by methyl triflate in 1,2-dichloroethane, forms in the first, fast kinetic step both linear polymer and cyclic dimer (D_4NMe). Subsequently a slow depolymerization process occurs leading to exclusively cyclotrisilazane (D_3NMe). On the basis of kinetic measurements carried out using an adiabatic calorimetric technique and complementary experiments, mechanisms of both propagation, cyclization and back-biting reactions are proposed. The influence of the reaction temperature was also studied; it is demonstrated that, at low temperature, polymerization does not lead to cyclic oligomer formation. In such conditions, the polymerization presents a ‘living’ character.     

Microfabrication by X‐ray‐induced polymerization above the lower critical solution temperature

A polymer synthesis method is presented in which chain growth driven by exothermic reaction stimulates a gradual chain collapse. The globular precipitates in such systems can be restrained from coalescing by polymerizing in a quiescent environment. Time‐resolved small‐angle scattering study of the methacrylic acid polymerization kinetics in a quiescent system above its lower critical solution temperature (LCST) in water reveals the following features of this method: (a) growing oligomers remain as rigid chains until a critical chain length is reached, at which they undergo chain collapse, (b) radius of gyration increases linearly with time until a critical conversion is reached, and (c) radius of gyration remains constant after the critical conversion, even while conversion is gradually increasing. Following this self‐stabilizing growth mechanism, we show that nanoparticles can be directly synthesized by polymerizing N‐isopropylacrylamide above its LCST in water. The average size of nanoparticles obtained from a polymer–solvent system is expected to be the maximum extent of reaction spread at that monomer concentration. This hypothesis was then verified by polymerizing N‐isopropylacrylamide above their LCST in water, but by initiating the reaction with X‐rays shielded by a mask. The microfabricated patterns conform well to the size and shape of the mask used confirming that the growing chains do not propagate beyond the exposed regions as long as the reaction temperature is maintained above the LCST. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 429–425, 2006     

纳米镓/聚甲基丙烯酸甲酯复合材料的原位超声合成与表征

超声作用于低熔点金属镓,使其超细化为纳米级的镓粒子,并采用无引发剂的乳液聚合方法制备出GA/聚甲基丙烯酸甲酯(PMMA)纳米复合粒子,并分析了其微观结构。结果表明纳米镓的形态和结构因有无表面改性剂而不同;乳液聚合得到的纳米镓复合粒子是核壳结构型,粒子大小为50~80 NM,内核金属镓粒径为30~50 NM,与聚合物存在一定的化学作用。     

有机镍化合物催化烯烃聚合的研究进展

综述了有机镍化合物如烯丙基镍、乙酰丙酮镍、茂镍、二亚胺镍等催化烯烃聚合的研究进展。有机镍化合物可催化烯烃、α-烯烃(如乙烯、丙烯等)的齐聚及聚合、催化极性单体(如甲基丙烯酸甲酯、降冰片烯等)以及位阻较大的环烯烃、取代二烯烃、苯乙烯等的均聚和共聚。     

用两亲聚合物制备大颗粒苯丙乳液

分别以两亲聚合物P(C9-AA)和P(DCPD-St-α-St-AA)作乳化荆，研究了制备大颗粒(约1μm)及具有一定稳定性的苯丙乳液的方法，讨论了乳化剂，温度及引发剂用量对乳液性能的影响。结果表明，以P(C9-AA)作乳化剂时，引发剂用量为单体质量的1．2％，90℃时可以合成性能良好的苯丙乳液；以P(DCPD-St-α-St-AA)作乳化荆时，引发剂用量为单体质量的1．2％，80℃时可以合成性能良好的苯丙乳液。     

块状镁基金属玻璃的研究进展

介绍了块状镁基金属玻璃的发展过程及最新的研究进展,着重阐述了块状镁基金属玻璃的几种制备方法及其性能,最后指出了今后块状镁基金属玻璃的研究重点.     

Surface modification of starch nanocrystals through ring‐opening polymerization of ε‐caprolactone and investigation of their microstructures

Bionanoparticles of starch obtained by submitting native potato starch granules to acid hydrolysis conditions. The resulted starch nanoparticles were used as core or macro initiator for polymerization of ε‐caprolactone (CL). Starch nanoparticle‐g‐polycaprolactone was synthesized through ring‐opening polymerization (ROP) of CL in the presence of Sn(Oct)₂ as initiator. The detailed microstructure of the resulted copolymer was characterized with NMR spectroscopy. Thermal characteristic of the copolymer was investigated using DSC and TGA. By introducing PCL, the range of melting temperature for starch was increased and degradation of copolymer occurred in a broader region. X‐ray diffraction and TEM micrographs confirmed that there was no alteration of starch crystalline structure and morphology of nanoparticles, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008