FW调剖技术及应用

应用FW调剖技术有针对性地对 119口非钻停井区注水井采取了 4种精细调剖方案 ,对比了化学浅调剖应用前后注水井层间矛盾的缓解 ,纵向上吸水剖面的改善 ,注水量和吸水指数的变化及渗流能力的变化。结果表明 ,注水井化学浅调剖后 ,井区的连通油井明显受效 ,获得较高的增油量 ,水驱的开发效果得到改善。化学浅调剖可以有效地封堵高渗透层 ,扩大低渗透层注入水的波及体积 ,减缓注水井层间矛盾 ,实现了对注水井吸水剖面的有效调整 ,这对深化注水结构调整、挖掘各类油层潜力、提高储量动用程度有显著的效果。     

生长温度对等离子体增强化学气相沉积生长ZnO薄膜质量的影响

以Zn(C2 H5) 2 和CO2 为反应源 ,在低温下用等离子体增强化学气相沉积方法 ,在Si衬底上外延生长了高质量的ZnO薄膜。用X射线衍射谱和光致发光谱研究了衬底温度对ZnO薄膜质量的影响。X射线衍射结果表明 ,在生长温度为2 3 0℃时制备出了高质量 ( 0 0 0 2 )择优取向的ZnO薄膜 ,其半高宽为 0 2 6°。光致发光谱显示出强的紫外自由激子发射与微弱的与氧空位相关的深缺陷发光 ,表明获得了接近化学配比的ZnO薄膜     

气液固三相相平衡热力学模型与计算方法

原油中含有大量的高分子有机固相物质，因此，要准确地描述油气体系相平衡，必须对气液固三相相平衡进行研究，在对高分子有机烃类沥青沉降机理有了一定的认识的基础上，提出了大的交互作用系数，可以描述沥青与原油中轻质不相容性的程度。根据对油气烃类混合物体系的一般性认识与提出的沥青组分特征化方法，导出了与之相应的有其自身特殊性的气液沥青三相相平衡物料平衡方程组，用考虑沥青沉降三相闪蒸数值算法，对沥青沉降进行有效的理化模拟计算，此外，结合实例分析，给出了沥青质参考逸度的计算，饱和压力和沉降量的拟合方法。     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

Potential use of phenolic antioxidants on peanut to control growth and aflatoxin B1 accumulation by Aspergillus flavus and Aspergillus parasiticus

Food‐grade antioxidants: butylated hydroxyanisole (BHA), propyl paraben (PP) and butylated hydroxytoluene (BHT) (10 and 20 mmol g^?1) and all the mixtures of these chemicals were tested for inhibitory activity on the growth of and aflatoxin B₁ (AFB₁) accumulation by Aspergillus parasiticus and A. flavus on irradiated (7 kGy) peanut grains. Also, the influence of these treatments was evaluated in different water conditions (0.982, 0.955, 0.937a_w) at 11 and 35 days of incubation at 28 °C. Water activity (a_w) affected the fungal growth, no fungal development was observed at the highest stress water condition (0.937a_w). Butylated hydroxyanisole at 10 mmol g^?1 level and all the mixtures with PP and/or BHT were significantly effective (P = 0.05) in increasing lag phase and reducing growth rate and colony forming units per gram of peanut of both Aspergillus section Flavi strains and AFB₁ accumulation. The application of BHA at concentrations of 20 mmol g^?1 alone or with PP and/or BHT totally inhibited fungal growth at 11 and 35 days of incubation. The results suggest that the addition of these chemical mixtures on peanut grains at low levels has potential to impact synergically on the control of Aspergillus section Flavi. Copyright © 2007 Society of Chemical Industry     

60Si2Mn合金钢发蓝泛红的分析研究

本文探讨了60Si2Mn合金钢发蓝原理，针对其膜层泛红问题，分析了热处理、表面前处理、发蓝及浸油等过程对发蓝质量的影响，由此采取了相应的技术措施，生产实践证明发蓝质量稳定，生产效率明显提高。     

服装低密度聚乙烯热熔胶化学粉碎的研究

服装粘合衬布的生产需要低密度聚乙烯热熔胶的微细粉末,介绍了对该热熔胶的化学粉碎技术所进行的实验研究,表明采用适当的助剂种类和用量以及适宜的工艺过程,通过化学粉碎可以得到合格的粉末产品。     

化学事故危害评估

根据化学事故危害的主要影响因素对化学事故进行危害评估,考查了危害纵深、人员杀伤率、危害地域估算、爆炸燃烧事故危害等内容。     

Al2O3对镁铬耐火材料致密化的影响

为了提高镁铬耐火材料的烧结性能,通过考察气孔率、体积密度和常温耐压强度与Al2O3加入量之间的关系,讨论了Al2O3添加剂对两种不同镁铬耐火材料致密化的影响.结果表明,镁铬耐火材料的骨料不同,Al2O3对其烧结性能和致密化的影响也不一样.